JVC DT-V1710CG Service Manual Download Page 49

Page: 49 / 76

(No. 52152) 1-49

CONTRAST ADJUSTMENT (SDTV)

Measuring Instruments

Signal generator (Crosshatch signal)
Oscilloscope

Card (Slot)

Component/RGB Input Card (Slot 1)

Test Points

TP-47G [CRT SOCKET PWB]
TP-GND [CRT SOCKET PWB]

Adjustment Points

S*01 (Contrast) [Service Menu]

Notes:

•

Perform the following adjustments after completing

the 1080/60i signal Contrast adjustment.

•

Set the CONTRAST data in the Setup Menu to "00".

•

The SR value (see the description of the HDTV

Contrast Adjustment) becomes the reference value
for the following adjustments. When this data is
changed, it is required to re-adjust the data of all of
the adjustment signals (HDTV, SDTV and NTSC/PAL).

When re-adjusting the 1080/60i signal, use the SI.

(1) Apply the 480/60i crosshatch signal to INPUT A (Terminal

Y on the Component/RGB Input Card).

(2) Set the CONTRAST potentiometer on the front panel to

the center click position.

(3) Connect the oscilloscope across TP-47G and TP-GND.
(4) Adjust

SE01

in the Service Menu to set the voltage

amplitude <A> in the figure on the right to the voltage
shown in the Table2.

(5) Vary the adjustment signal and adjustment data, and re-

perform adjustments in steps 1 to 4 above (see Table 2).

1 Vertical interval

(V. sync)

<A>

Adjustment Signal Adjustment Data Adjustment Voltage <A>

480/60i

SE01

36 V ± 2 V

576/50i

SF01

36 V ± 2 V

480/60p

SG01

35 V ± 2 V

576/50p

SH01

35 V ± 2 V

Table 2

Summary of Contents for DT-V1710CG













































































Search results

Summary of Contents for DT-V1710CG

Reviews:

JVC DT-V1710CG, Service Manual, Page: 49 / 76

Search results

Summary of Contents for DT-V1710CG

Reviews: