JVC DT-V1710CG Service Manual Download Page 47

Page: 47 / 76

(No. 52152) 1-47

CONVERGENCE ADJUSTMENT

Measuring Instruments

Signal generator (Crosshatch signal with circle pattern)

Card (Slot)

Component/RGB Input Card (Slot 1)

Test Points

Adjustment Points

VR504 (CONV_H) [S. CORRECTION PWB]
VR505 (CONV_V) [S. CORRECTION PWB]

Notes:

•

Perform the following adjustments after completing the Screen

Voltage Coarse adjustment, X-Ray Protector, High Voltage and
Focus adjustments.

•

Ensure that CN0RD and CN00R on the S. Correction PWB are

connected to the Deflection yoke and Main PWB.

(1) Set the

VR504

and

VR505

on S. CORRECTION PWB into the position

of a center.

(2) Apply the 1080/60i crosshatch signal with circle pattern to INPUT A

(Terminal Y on the Component/RGB Input Card).

(3) Turn the

VR504

to optimize the horizontal convergence value at the

center of the screen (turning the potentiometer counterclockwise shifts
BLUE toward the right with respect to RED).

(4) Turn the

VR505

to optimize the vertical convergence value at the center

of the screen (turning the potentiometer counterclockwise shifts BLUE
downward with respect to RED).

4.10.7 CONVERGENCE ADJUSTMENT

S. CORRECTION PWB

MAIN PWB

Front side

TP-XR

TP-G

Front side

(Left)

(Right)

(Upper)

(Lower)

VR505 [CONV_V]

VR504 [CONV_H]

VR502 [H.VOLTAGE]

VR501 [X-RAY]

CN0RD

CN00R

(Top surface view of S. CORRECTION PWB)

VR505

VR504

VR505

VR504

VR502

VR501

CN0RD

CN00R

Escutcheon

Area A

Area B

Aberration of color

≤

0.25mm

≤

0.35mm

Summary of Contents for DT-V1710CG













































































Search results

Summary of Contents for DT-V1710CG

Reviews:

JVC DT-V1710CG, Service Manual, Page: 47 / 76

Search results

Summary of Contents for DT-V1710CG

Reviews: