JVC DT-V1710CG Service Manual Download Page 48

Page: 48 / 76

1-48 (No. 52152)

CONTRAST ADJUSTMENT (HDTV)

Notes:

•

Perform the following adjustments after completing

the Screen Voltage Coarse adjustment.

•

Set the CONTRAST data in the Setup Menu to “00”.

•

The value adjusted at the SR adjustment becomes

the reference value for the following adjustments.
When this data is changed, it is required to re-adjust
the data of all of the adjustment signals (HDTV, SDTV
and NTSC/PAL). When re-adjusting the 1080/60i
signal, use the SI.

– Standard value (SR) adjustment –

(1) Apply the 1080/60i crosshatch signal to INPUT A (Terminal

Y on the Component/RGB Input Card).

(2) Set the CONTRAST potentiometer on the front panel to

the center click position.

(3) Connect the oscilloscope across TP-47G and TP-GND.
(4) Adjust

SR01

in the Service Menu to set the voltage

amplitude <A> in the figure on the right to the voltage
shown in the Table 1.

– Other signals adjustments –

(5) Apply the 1080/60i crosshatch signal to INPUT A (Terminal

Y on the Component/RGB Input Card).

(6) Set the CONTRAST potentiometer on the front panel to

the center click position.

(7) Connect the oscilloscope across TP-47G and TP-GND.
(8) Adjust

SI01

in the Service Menu to set the voltage

amplitude <A> in the figure on the right to the voltage
shown in the Table 1.

(9) Vary the adjustment signal and adjustment data, and

re-perform adjustments in steps 5 to 8 above (see Table
1).

4.10.8 CONTRAST ADJUSTMENTS

1 Vertical interval

(V. sync)

<A>

Adjustment Signal Adjustment Data Adjustment Voltage <A>

COMMON(1080/60i)

SR1

30 V ± 2 V

1080/60i

SI01

30 V ± 2 V

1080/50i

SK01

32 V ± 2 V

1080/24spF

SL01

33 V ± 2 V

720/60p

SM01

32 V ± 2 V

720/50p

SN01

32 V ± 2 V

Table 1

Measuring Instruments

Signal generator (Crosshatch signal)
Oscilloscope

Card (Slot)

Component/RGB Input Card (Slot 1)

Test Points

TP-47G [CRT SOCKET PWB]
TP-GND [CRT SOCKET PWB]

Adjustment Points

S*01 (Contrast) [Service Menu]

Summary of Contents for DT-V1710CG













































































Search results

Summary of Contents for DT-V1710CG

Reviews:

JVC DT-V1710CG, Service Manual, Page: 48 / 76

Search results

Summary of Contents for DT-V1710CG

Reviews: