JVC DT-V1710CG Service Manual Download Page 52

Page: 52 / 76

1-52 (No. 52152)

CHROMA/PHASE ADJUSTMENTS (COMPONENT)

Measuring Instruments

Signal generator (Color bar signal)
Oscilloscope

Card (Slot)

Component/RGB Input Card (Slot 1)

Test Points

TP-47B [CRT SOCKET PWB]
TP-GND [CRT SOCKET PWB]

Adjustment Points

S*03 (Chroma), S*04 (Phase) [Service Menu]

Notes:

•

Perform the following adjustments after completing

the Contrast adjustment.

•

Set the CHROMA and PHASE data in the Setup Menu

to “00”.

•

The value adjusted at the SR adjustment becomes the

reference value for the following adjustments. When
this data is changed, it is required to re-adjust the
data of all of the adjustment signals (Component,
NTSC and PAL). When re-adjusting the 1080/60i signal,
use the SI.

(1) Apply the 1080/60i component color bar signal to INPUT A.
(2) Set the CHROMA and PHASE potentiometers on the front

panel to the center click positions.

(3) Connect the oscilloscope across TP-47B and TP-GND.
(4) Adjust

SR03

in the Service Menu to set the level difference

between waveforms 1 and 4 in the figure on the right to

0 V

± 2 V

(5) Adjust

SR04

to set the level difference between 1 and 3 to

V ± 2 V

(6) Vary the adjustment signal and adjustment data, and re-

perform adjustments in steps 1 to 5 above (see Table 5).

4.10.9 CHROMA/PHASE ADJUSTMENTS

Table 5

Adjustment

Adjustment Data

Signal

Chroma

Phase

COMMON

SR03

SR04

1080/60i

SI03

SI04

1080/50i

SK03

SK04

1080/24psF

SL03

SL04

720/60p

SM03

SM04

720/50p

SN03

SN04

480/60i

SE03

SE04

576/50i

SF03

SF04

480/60p

SG03

SG04

576/50p

SH03

SH04

Summary of Contents for DT-V1710CG













































































Search results

Summary of Contents for DT-V1710CG

Reviews:

JVC DT-V1710CG, Service Manual, Page: 52 / 76

Search results

Summary of Contents for DT-V1710CG

Reviews: