manualshive.com logo in svg

JVC DT-V1710CG, Service Manual, Page: 63 / 76

Share
Download
JVC DT-V1710CG Service Manual Download Page 63

(No. 52152)  1-63

VERTICAL IMAGE POSITION, IMAGE AMPLITUDE AND IMAGE DISTORTION ADJUSTMENTS (NTSC/PAL OVERSCAN 16:9 MODE)

(1) Apply the NTSC mono-scope signal to INPUT C (Terminal

VIDEO1 on the NTSC/PAL Video Input Card).

(2) Press the ASPECT button on the front panel to set the

scanning size to 16:9 mode.

(3) Set the CONTRAST and BRIGHT potentiometers on the

front panel to the center click positions.

(4) Adjust 

DY02 

in the Service Menu to set the vertical position

of the image at the center of the CRT screen.

(5) Adjust 

DY01 

to set the vertical amplitude of the image to

193mm

.

(6) Apply the NTSC crosshatch signal to INPUT C.
(7) Adjust 

CE08 

to optimize the trapezoidal distortion (observe

the second vertical lines from the left and right edges as the
reference).

(8) Adjust 

CE07 

to optimize the parallelogram distortion (observe

the second vertical lines from the left and right edges as the
reference).

(9) Adjust 

CE09 

to optimize the horizontal arc distortion.

(10)Adjust 

DY03 

so that the second vertical lines from the left

and right edges are linear.

(11) If there is an extreme corner S-shape distortion, adjust 

CE06

to optimize it (this adjustment is usually unnecessary).

(12)If there is an extreme corner W-shape distortion, adjust 

CE05

to optimize it (this adjustment is usually unnecessary).

(13)Apply the NTSC mono-scope signal to INPUT C.
(14)Ensure that the vertical amplitude of the image is 

193mm

. If

it is not, adjust 

DY01 

again.

(15)Adjust 

DY02 

so that the vertical position of the image comes

at the center of the CRT screen.

(16)Vary the adjustment signal and adjustment data, and re-

perform adjustments in steps 1 to 15 above (see Table 16).

90

90

80

80

80

193mm

90

Make these lines linear.

Screen size

Adjustment Adjustment

Adjustment Data

Step No.

Signal

Vertical

Vertical

Side Pin

Corner

Corner

Parallelogram Trapezoidal

Horizontal

Position

size

Distortion Distortion (W) Distortion (S)

Distortion

Distortion  Arc Distortion

1

NTSC

DY02

DY01

DY03

CE05

CE06

CE07

CE08

CE09

2

PAL

DY08

DY07

DY09

CE10

CE11

CE12

CE13

CE14

Table 16

Notes:

•

Perform the following adjustments after completing the Reference Mode (NTSL/PAL overscan 4:3 mode) adjustment.

•

The corner distortions (W) & (S), parallelogram distortion, trapezoidal distortion and horizontal arc distortion adjustment
data for this adjustment are common to those in the NTSC/PAL overscan 16:9 mode and the NTSC/PAL underscan 16:9

mode adjustments. This adjustment data needs to be adjusted in either mode.

•

The corner distortions (W) & (S), parallelogram distortion, trapezoidal distortion and horizontal arc distortion adjustment
data for this adjustment are common to those in the 480/60i and NTSC signal or 576/50i and PAL signal adjustments.

This adjustment data needs to be adjusted with either signal.

Measuring Instruments

Signal generator (Mono-scope signal, Crosshatch signal)

Card (Slot)

NTSC/PAL Video Input Card (Slot 2)

Test Points
Adjustment Points

DY** (Vertical Size), DY** (Vertical Position), DY** (Side Pin Distortion), CE** (Corner Distortion
(W)), CE** (Corner Distortion (S)), CE** (Parallelogram Distortion), CE** (Trapezoidal Distortion),
CE** (Horizontal Arc Distortion) [Service Menu]

Summary of Contents for DT-V1710CG













































































Reviews:

No comments