manualshive.com logo in svg

JVC DT-V1710CG, Service Manual, Page: 43 / 76

Share
Download
JVC DT-V1710CG Service Manual Download Page 43

(No. 52152)  1-43

4.10 ADJUSTMENT PROCEDURES

SCREEN VOLTAGE COARSE ADJUSTMENT

Measuring Instruments

Signal generator (All-black signal, Crosshatch signal)
Oscilloscope

Card (Slot)

Component/RGB Input Card (Slot 1)

Test Points

Anode of CRT
TP-47B, TP-47R, TP-47G [CRT SOCKET PWB]
TP-GND [CRT SOCKET PWB]

Adjustment Points

SCREEN VR [Bottom potentiometer on high-voltage transformer]
VR502 (High-voltage VR) [S.CORRECTION PWB]
FOCUS VR1 [Top potentiometer on high-voltage transformer]
FOCUS VR2 [Middle potentiometer on high-voltage transformer]
CC41 (AKB Setting) [Service Menu]

Note: Ensure that the value of CC41 (CPU BLOCK) in the Service Menu is 

“

000

”

.

(1) Turn the SCREEN VR fully counterclockwise.

(2) Connect the oscilloscope across TP-47B and TP-GND.

(3) Connect the GND of high-voltage voltmeter to the braided wire.

(4) Connect the high-voltage voltmeter to the anode of the CRT and turn the

unit ON.

(5) Apply the 1080/60i component all-black signal to INPUT A.

(6) Check that the high-voltage value is

 24

 to 

25 kV

. If it is higher than 

25 kV

,

adjustment the

 VR502

 so that the high-voltage value becomes to specified value.

(7) Turn the

 SCREEN VR

 slowly clockwise until the raster lights up slightly.

(8) Set the value of 

CC41 (CPU BLOCK)

 in the Service Menu from “000” to “002”.

(9) Turn the 

SCREEN VR

 slowly clockwise until the voltage amplitude <A> of

the AKB pulse at TP-47G is about 

25 V ± 2 V

.

(10)Observe the waveforms of TP-47R and TP-47B, adjust the SCREEN VR so

that the amplitude voltage <A> of the AKB pulse become to 

25V ± 2V

.

(11) Apply the 1080/60i crosshatch signal to INPUT A.

(12)Adjust the 

FOCUS VR1

 and 

VR2

 so that the entire image is in focus.

1 Vertical interval

(V. sync)

AKB pulse

V.BLK

<A>
25V ± 2V

4.10.1 SCREEN VOLTAGE COARSE ADJUSTMENT

HIGH-VOLTAGE COARSE ADJUSTMENT

Measuring Instruments

Signal generator (Crosshatch signal with circle pattern)
High-voltage voltmeter

Card (Slot)

Component/RGB Input Card (Slot 1)

Test Points

Anode of CRT

Adjustment Points

VR502 (High-Voltage VR) [S. CORRECTION PWB]
FOCUS VR1 [Top potentiometer on high-voltage transformer]
FOCUS VR2 [Middle potentiometer on high-voltage transformer]

Note: Perform the following adjustments after completing the Screen Voltage Coarse adjustment.

(1) Turn 

VR502

 fully clockwise (the minimum position).

(2) Turn 

VR501

 fully counterclockwise (the minimum position).

(3) Connect the high-voltage voltmeter to the anode of the CRT and turn the unit ON.

(4) Apply the 1080/60i crosshatch signal with circle pattern to INPUT A (Terminal Y on the Component/RGB Input Card).

(5) Turn 

VR502

 slowly counterclockwise until the value of the high voltage is about 

25 kV

.

(6) Adjust the

 FOCUS VR1

 and 

VR2 

so that the entire image is in focus.

4.10.2 HIGH-VOLTAGE COARSE ADJUSTMENT

S. CORRECTION PWB

MAIN PWB

Front side

TP-XR

TP-G

Front side

(Min)

(Max)

(Min)

(Max)

VR505 [CONV_V]

VR504 [CONV_H]

VR502 [H.VOLTAGE]

VR501 [X-RAY]

CN0RD

CN00R

(Top surface view of the S. CORRECTION PWB)

VR505

VR504

VR502

VR501

CN0RD

CN00R

VR502

VR501

Summary of Contents for DT-V1710CG













































































Reviews:

No comments