JVC DT-V1710CG Service Manual Download Page 50

Page: 50 / 76

1-50 (No. 52152)

CONTRAST ADJUSTMENT (NTSC/PAL VIDEO)

Measuring Instruments

Signal generator (Crosshatch signal)
Oscilloscope

Card (Slot)

NTSC/PAL Video Input Card (Slot 2)

Test Points

TP-47G [CRT SOCKET PWB]
TP-GND [CRT SOCKET PWB]

Adjustment Points

S*01 (Contrast) [Service Menu]

Notes:

•

Ensure that the output waveforms from the NTSC/

PAL Video Input Cards are normal before proceeding
to the following adjustments.

•

Perform the following adjustments after completing

the 1080/60i signal Contrast Adjustment.

•

Set the CONTRAST data in the Setup Menu to “00”.

•

The SO value (see the description of the HDTV

Contrast Adjustment) becomes the reference value
for the following adjustments. When this data is
changed, it is required to re-adjust the data of all of
the adjustment signals (HDTV, SDTV and NTSC/PAL).

When re-adjusting the 1080/60i signal, use the SI. (For

the adjustment of the 1080/60i signal, use the
Component/RGB Input Card.)

(1) Apply the NTSC crosshatch signal to INPUT C (Terminal

VIDEO1 on the NTSC/PAL Video Input Card).

(2) Set the CONTRAST potentiometer on the front panel to

the center click position.

(3) Connect the oscilloscope across TP-47G and TP-GND.
(4) Adjust

SA01

in the Service Menu to set the voltage

amplitude <A> in the figure on the right to the voltage shown
in the Table 3.

(5) Vary the adjustment signal and adjustment data, and re-

perform adjustments in steps 1 to 4 above (see Table 3).

1 Vertical interval

(V. sync)

<A>

Adjustment Signal Adjustment Data Adjustment Voltage <A>

NTSC (VIDEO)

SA01

36 V ± 2 V

PAL (VIDEO)

SC01

36 V ± 2 V

Table 3

Summary of Contents for DT-V1710CG













































































Search results

Summary of Contents for DT-V1710CG

Reviews:

JVC DT-V1710CG, Service Manual, Page: 50 / 76

Search results

Summary of Contents for DT-V1710CG

Reviews: