manualshive.com logo in svg

JVC DT-V1710CG, Service Manual, Page: 3 / 76

Share
Download
JVC DT-V1710CG Service Manual Download Page 3

(No. 52152)  1-3

1.1 SAFETY PRECAUTIONS

(1) The design of this product contains special hardware,

many circuits and components specially for safety

purposes. For continued protection, no changes should

be made to the original design unless authorized in writing

by the manufacturer. Replacement parts must be identical

to those used in the original circuits. Service should be

performed by qualified personnel only.

(2) Alterations of the design or circuitry of the products should

not be made. Any design alterations or additions will void

the manufacturer's warranty and will further relieve the

manufacturer of responsibility for personal injury or

property damage resulting therefrom.

(3) Many electrical and mechanical parts in the products have

s p e c i a l   s a f e t y - r e l a t e d   c h a r a c t e r i s t i c s .  T h e s e

characteristics are often not evident from visual inspection

nor can the protection afforded by them necessarily be

obtained by using replacement components rated for

higher voltage, wattage, etc. Replacement parts which

have these special safety characteristics are identified in

the parts list of Service manual. 

Electrical components

having such features are identified by shading on

the schematics and by (   ) on the parts list in Service

manual.

 The use of a substitute replacement which does

not have the same safety characteristics as the

recommended replacement part shown in the parts list of

Service manual may cause shock, fire, or other hazards.

(4)

Use isolation transformer when hot chassis.

The chassis and any sub-chassis contained in some

products are connected to one side of the AC power line.

An isolation transformer of adequate capacity should be

inserted between the product and the AC power supply

point while performing any service on some products when

the HOT chassis is exposed.

(5)

Don't short between the LIVE side ground and

ISOLATED (NEUTRAL) side ground or EARTH side

ground when repairing.

Some model's power circuit is partly different in the GND.

The difference of the GND is shown by the LIVE : (   ) side

GND, the ISOLATED(NEUTRAL) : (   ) side GND and EARTH

: ( 

 ) side GND. Don't short between the LIVE side GND

and ISOLATED(NEUTRAL) side GND or EARTH side GND

a n d   n e v e r   m e a s u r e   t h e   L I V E   s i d e   G N D   a n d

ISOLATED(NEUTRAL) side GND or EARTH side GND at the

same time with a measuring apparatus (oscilloscope etc.).

If above note will not be kept, a fuse or any parts will be

broken.

(6) If any repair has been made to the chassis, it is

recommended that the B1 setting should be checked or

adjusted (See ADJUSTMENT OF B1 POWER SUPPLY).

(7) The high voltage applied to the picture tube must conform

with that specified in Service manual. Excessive high

voltage can cause an increase in X-Ray emission, arcing

and possible component damage, therefore operation

under excessive high voltage conditions should be kept

to a minimum, or should be prevented. If severe arcing

occurs, remove the AC power immediately and determine

the cause by visual inspection (incorrect installation,

cracked or melted high voltage harness, poor soldering,

etc.). To maintain the proper minimum level of soft X-Ray

emission, components in the high voltage circuitry

including the picture tube must be the exact replacements

or alternatives approved by the manufacturer of the

complete product.

(8) Do not check high voltage by drawing an arc. Use a high

voltage meter or a high voltage probe with a VTVM.

Discharge the picture tube before attempting meter

connection, by connecting a clip lead to the ground frame

and connecting the other end of the lead through a 10k

Ω

2W resistor to the anode button.

(9) When service is required, observe the original lead dress.

Extra precaution should be given to assure correct lead

dress in the high voltage circuit area. Where a short circuit

has occurred, those components that indicate evidence

of overheating should be replaced. Always use the

manufacturer's replacement components.

(10)

Isolation Check

(Safety for Electrical Shock Hazard)

After re-assembling the product, always perform an

isolation check on the exposed metal parts of the cabinet

(antenna terminals, video/audio input and output terminals,

Control knobs, metal cabinet, screwheads, earphone jack,

control shafts, etc.) to be sure the product is safe to operate

without danger of electrical shock.

a)

Dielectric Strength Test

The isolation between the AC primary circuit and all metal

parts exposed to the user, particularly any exposed metal

part having a return path to the chassis should withstand

a voltage of 1100V AC (r.m.s.) for a period of one second.

(. . . . Withstand a voltage of 1100V AC (r.m.s.) to an

appliance rated up to 120V, and 3000V AC (r.m.s.) to an

appliance rated 200V or more, for a period of one second.)

This method of test requires a test equipment not generally

found in the service trade.

b)

Leakage Current Check

Plug the AC line cord directly into the AC outlet (do not

use a line isolation transformer during this check.). Using

a “Leakage Current Tester”, measure the leakage current

from each exposed metal part of the cabinet, particularly

any exposed metal part having a return path to the chassis,

to a known good earth ground (water pipe, etc.). Any

leakage current must not exceed 0.5mA AC (r.m.s.).

However, in tropical area, this must not exceed 0.2mA AC

(r.m.s.).

•

Alternate Check Method

Plug the AC line cord directly into the AC outlet (do not

use a line isolation transformer during this check.). Use

an AC voltmeter having 1000 ohms per volt or more

sensitivity in the following manner. Connect a 1500

Ω

 10W

resistor paralleled by a 0.15µF AC-type capacitor

between an exposed metal part and a known good earth

ground (water pipe, etc.). Measure the AC voltage across

the resistor with the AC voltmeter. Move the resistor

connection to each exposed metal part, particularly any

exposed metal part having a return path to the chassis,

and measure the AC voltage across the resistor. Now,

reverse the plug in the AC outlet and repeat each

measurement. Any voltage measured must not exceed

0.75V AC (r.m.s.).  This corresponds to 0.5mA AC (r.m.s.).

However, in tropical area, this must not exceed 0.3V AC

(r.m.s.).  This corresponds to 0.2mA AC (r.m.s.).

(11)

High voltage hold down circuit check.

After repair of the high voltage hold down circuit, this circuit

shall be checked to operate correctly.

See 

“X-RAY PROTECTOR ADJUSTMENT/CHECK”

 on

page 1-44.

GOOD
EARTH
GROUND

0.15 µF  AC-TYPE

AC VOLTMETER
(HAVING 1000

Ω

/V,

OR MORE SENSITIVITY)

PLACE THIS PROBE
ON EACH EXPOSED
METAL PART

1500

Ω

  10W

A          V

This mark shows a fast

POWER CORD
REPLACEMENT WARNING

Connecting the white line side of
power cord to “WHT” character side.

operating fuse, the
letters indicated below
show the rating.

PWB

WHT

PW

White line side

SECTION 1

PRECAUTION

Summary of Contents for DT-V1710CG













































































Reviews:

No comments