manualshive.com logo in svg

Juniper JUNOS 10.1 - S 5-13-2010, Release Note

The Juniper JUNOS 10.1 - S 5-13-2010 is a cutting-edge networking software, offering enhanced performance and security. Stay updated with the latest features and improvements by downloading the free Release Note manual from manualshive.com. Discover new possibilities and optimize your network effortlessly with this advanced product.

Share
Download
background image

■

Errata and Changes in Documentation for JUNOS Software Release 10.1 for M
Series, MX Series, and T Series Routers on page 86

■

Upgrade and Downgrade Instructions for JUNOS Release 10.1 for M Series, MX
Series, and T Series Routers on page 89

Errata and Changes in Documentation for JUNOS Software Release 10.1 for M Series, MX
Series, and T Series Routers

Changes to the JUNOS Documentation Set

The title of the 

JUNOS Hierarchy and RFC Reference

 is now 

JUNOS Hierarchy and

Standards Reference

.

Documentation for the extended DHCP relay agent feature is no longer included in
the 

Policy Framework Configuration Guide

. For DHCP relay agent documentation, see

the 

Subscriber Access Configuration Guide

 or the documentation for subscriber access

management.

The new JUNOS Technical Documentation index page
(

http://www.juniper.net/techpubs/software/junos/index.html

 ) consolidates documentation

for JUNOS Software features that are common to all platforms that run JUNOS
Software. The new index page provides direct access to core JUNOS information and
links to information for JUNOS features that run on particular platforms.

Errata

This section lists outstanding issues with the documentation.

High Availability

■

TX Matrix Plus routers and T1600 routers that are configured as part of a routing
matrix do not currently support nonstop active routing. [

High Availability

]

Integrated Multi-Services Gateway (IMSG)

■

Chapter 15

, 

Maintenance and Failover in the IMSG

, describes the IMSG high

availability feature. This feature is not supported in this release of the software.

[

Multiplay Solutions

]

Interfaces and Chassis

■

The 

Configuring ECMP Next Hops for RSVP and LDP LSPs for Load Balancing

 topic

in the 

System Basics Configuration Guide

 does not mention the following caveat

for configuring ECMP next hops for RSVP LSPs:

If RSVP LSPs are configured with bandwidth allocation, for ECMP next hops with
more than 16 LSPs, traffic is not distributed optimally based on bandwidths

86

■

Errata and Changes in Documentation for JUNOS Software Release 10.1 for M Series, MX Series, and T Series Routers

JUNOS 10.1 Software Release Notes

Summary of Contents for JUNOS 10.1 - S 5-13-2010













































































































































































































Reviews:

No comments

Related manuals for JUNOS 10.1 - S 5-13-2010

Native Instruments Reaktor Spark Manual preview
Reaktor Spark
Brand: Native Instruments Pages: 38
Hitachi Universal Storage Platform VM Installation Planning Manual preview
Universal Storage Platform VM
Brand: Hitachi Pages: 62
Hitachi Universal Storage Platform V Reference Manual preview
Universal Storage Platform V
Brand: Hitachi Pages: 102
Hitachi MK-96RD626-07 User Manual preview
MK-96RD626-07
Brand: Hitachi Pages: 205
Extreme Networks Ridgeline 3.0 Manual preview
Ridgeline 3.0
Brand: Extreme Networks Pages: 376
Red Hat CLUSTER SUITE - FOR RHEL 4 Overview preview
CLUSTER SUITE - FOR RHEL 4
Brand: Red Hat Pages: 74
Omron SYSMAC CX-Programmer 9 Operation Manual preview
SYSMAC CX-Programmer 9
Brand: Omron Pages: 232
EVGA PCoIP Technology User Manual preview
PCoIP Technology
Brand: EVGA Pages: 27
URC Total Control Mobile Installation & Programming preview
Total Control Mobile
Brand: URC Pages: 14
Oracle Secure Backup 10.3 Installation And Configuration Manual preview
Secure Backup 10.3
Brand: Oracle Pages: 174
Genius VIDEOCAM SLIMCLIP Installation Manual preview
VIDEOCAM SLIMCLIP
Brand: Genius Pages: 7
Cabletron Systems SSR-ATM29-02 User Manual preview
SSR-ATM29-02
Brand: Cabletron Systems Pages: 386
National Instruments NI-VXI User Manual preview
NI-VXI
Brand: National Instruments Pages: 149
Velocity SEAL-IT SEAL-IT 100 User Manual preview
SEAL-IT SEAL-IT 100
Brand: Velocity Pages: 38
Fujitsu ScanSnap Upgrade User Manual preview
ScanSnap Upgrade
Brand: Fujitsu Pages: 55
JVC GY-HM700U - Prohd Compact Shoulder Solid State Camcorder Manual preview
GY-HM700U - Prohd Compact Shoulder Solid State Camcorder
Brand: JVC Pages: 780
HP AA-RLE1C-TE Getting Started preview
AA-RLE1C-TE
Brand: HP Pages: 100
HP B2355-92068 Administration Manual preview
B2355-92068
Brand: HP Pages: 622

Brands by name

Popular brands

Load more brands