manualshive.com logo in svg

Juniper JUNOS 10.1 - S 5-13-2010, Release Note

The Juniper JUNOS 10.1 - S 5-13-2010 is a cutting-edge networking software, offering enhanced performance and security. Stay updated with the latest features and improvements by downloading the free Release Note manual from manualshive.com. Discover new possibilities and optimize your network effortlessly with this advanced product.

Share
Download
background image

Flow and Processing

■

On SRX210 devices, the lowest rate ATM CoS PCR supported was 64 Kbps. The
ping operation did not reach an ATM interface with a PCR lower than 64 Kbps.
[PR/470994: This issue has been resolved.]

■

On SRX3400, SRX3600, SRX5600, and SRX5800 devices, in Layer 2 mode, IGMP
and multicast were supported only on the 224.X.X.X address. [PR/493166: This
issue has been resolved.]

Hardware

■

On SRX210 devices, the system took between 2 and 5 minutes to initialize.
[PR/298635: This issue has been resolved.]

■

On SRX240 devices, when users swapped the USBs after startup, the
chassis-control subsystem did not respond to any chassis-related commands.
[PR/437798: This issue has been resolved.]

■

On SRX210 Low Memory devices, 3G AC402 Live Network Card activation got
timed out. [PR/451493: This issue has been resolved.]

Infrastructure

■

On SRX5600 and SRX5800 devices, e2e.trace showed an incorrect PIC number
for the egress message. [PR/487331: This issue has been resolved.]

Integrated Convergence Services

■

Unable to edit the media gateway IP address field on the peer call server page
in J-Web. [PR/445750: This issue has been resolved.]

■

The J-Web Call Feature 

Add

 button did not work. [PR/446422: This issue has

been resolved.]

■

Was not able to edit the extension number on the J-Web call features page.
[PR/447523: This issue has been resolved.]

■

When you edited the remote access number in J-Web, the change was not
displayed until you refreshed the page. [PR/447530: This issue has been resolved.]

■

Caller ID was not displayed on FXS stations for FXO to FXS calls in survivable
call server (SRX Series SCS) state. [PR/451719: This issue has been resolved.]

■

In J-Web, you were not able specify the station type (as either analog or SIP).
[PR/452813: This issue has been resolved.]

■

On SRX210 devices with Integrated Convergence Services, in J-Web, a commit
was completed when a trunk group was configured without one or more trunks,
but the trunk group configuration was not visible in J-Web or the CLI. [PR/460489:
This issue has been resolved.]

■

The voice prompt was not played when the user dialed an invalid extension.
[PR/472357: This issue has been resolved.]

Issues in JUNOS Release 10.1 for SRX Series Services Gateways and J Series Services Routers

■

159

Issues in JUNOS Release 10.1 for SRX Series Services Gateways and J Series Services Routers

Summary of Contents for JUNOS 10.1 - S 5-13-2010













































































































































































































Reviews:

No comments

Related manuals for JUNOS 10.1 - S 5-13-2010

Samsung MZ-7PC128N User Manual preview
MZ-7PC128N
Brand: Samsung Pages: 59
Cisco 2950C-24 - Catalyst Switch - Stackable Datasheet preview
2950C-24 - Catalyst Switch - Stackable
Brand: Cisco Pages: 18
Cisco CONFERENCING EXTENSIONS - ADMINISTRATOR GUIDE FOR MICROSOFT EXCHANGE Administrator'S Manual preview
CONFERENCING EXTENSIONS - ADMINISTRATOR GUIDE FOR MICROSOFT EXCHANGE
Brand: Cisco Pages: 61
Cisco Cisco mds 9124 - fabric switch Datasheet preview
Cisco mds 9124 - fabric switch
Brand: Cisco Pages: 9
Cisco CISCO1811 End User Instructions preview
CISCO1811
Brand: Cisco Pages: 16
Cisco Cisco MDS 9020 - Fabric Switch Configuration Manual preview
Cisco MDS 9020 - Fabric Switch
Brand: Cisco Pages: 22
Cisco Catalyst X6816 Datasheet preview
Catalyst X6816
Brand: Cisco Pages: 13
Cisco Cisco mds 9124 - fabric switch Specifications preview
Cisco mds 9124 - fabric switch
Brand: Cisco Pages: 3
Cisco DCNM Configuration preview
DCNM
Brand: Cisco Pages: 7
Cisco GEM318P User Manual preview
GEM318P
Brand: Cisco Pages: 74
Cisco Craft Works Interface Quick Start Manual preview
Craft Works Interface
Brand: Cisco Pages: 32
Cisco Catalyst Series Switch 2940 Hardware Installation Manual preview
Catalyst Series Switch 2940
Brand: Cisco Pages: 82
Cisco Catalyst Series Switch 2940 Regulatory Compliance And Safety Information Manual preview
Catalyst Series Switch 2940
Brand: Cisco Pages: 28
Cisco 11.0 BT Release Notes preview
11.0 BT
Brand: Cisco Pages: 58
Cisco CCNA NETWORK SIMULATOR Manual preview
CCNA NETWORK SIMULATOR
Brand: Cisco Pages: 88
Cisco CSACSE-1111-K9 - Secure Access Control Server Solution Engine Installation Manual preview
CSACSE-1111-K9 - Secure Access Control Server Solution Engine
Brand: Cisco Pages: 130
Cisco IP Communicator Administration Manual preview
IP Communicator
Brand: Cisco Pages: 162
Cisco HSI 4.1 User Manual preview
HSI 4.1
Brand: Cisco Pages: 199

Brands by name

Popular brands

Load more brands