manualshive.com logo in svg

Juniper JUNOS 10.1 - S 5-13-2010, Release Note

The Juniper JUNOS 10.1 - S 5-13-2010 is a cutting-edge networking software, offering enhanced performance and security. Stay updated with the latest features and improvements by downloading the free Release Note manual from manualshive.com. Discover new possibilities and optimize your network effortlessly with this advanced product.

Share
Download
background image

USB Modem

■

On SRX210, SRX100, SRX240, and SRX650 devices, when you restart fwdd at
the dial-out side, the umd interface goes down and the call never gets connected.
As a workaround, disable the dialer interface and restart the forwarding daemon.
Enable the dialer interface when the forwarding daemon is up and running. As
a result the dial-out side reconnects with the dial-in side successfully.

Perform the following steps:

1.

Disable the dialer interface.

root@noky# set interfaces dl0 disable

root@noky# commit

2.

Restart the forwarding daemon.

root@noky# run restart forwarding Forwarding Daemon started, pid 1407

root@noky# delete interfaces dl0 disable

root@noky# commit

3.

Enable the dialer interface.

root@noky# delete interfaces dl0 disable

root@noky# commit

[PR/480206]

■

On SRX210 High Memory devices and J6350 devices, packet loss is seen during
rapid ping operations between the dialer interfaces when packet size is more
than 512 Kbps. [PR/484507]

■

On SRX210 High Memory devices, the modem interface can handle bidirectional
traffic of up to 19 Kbps. During oversubscription of 20-Kbps or more traffic, the
keepalive packets are not exchanged and the interface goes down. [PR/487258]

■

On SRX210 High Memory devices, IPv6 is not supported on dialer interfaces
with a USB modem. [PR/489960]

■

On SRX210 High Memory devices, http traffic is very slow through the umd0
interface. [PR/489961]

■

On SRX210 High Memory devices, on multiple resets of the umd0 interface, the
umd0 interface keeps flapping if the d10 (dialer) interface on either the dialin
or dialout interface goes down because no keepalive packets are exchanged. As
a workaround, increase the ATS0 value to 4 or greater. [PR/492970]

■

On SRX100, SRX210, SRX240, and SRX650 devices, the call terminates if you
remove and insert a USB modem. [PR/491820]

■

On SRX210 High Memory devices and J6350 devices, the D10 link flaps during
long-duration traffic of 15 Kbps and also when packet size is 256 Kbps or more.
[PR/493943]

156

■

Issues in JUNOS Release 10.1 for SRX Series Services Gateways and J Series Services Routers

JUNOS 10.1 Software Release Notes

Summary of Contents for JUNOS 10.1 - S 5-13-2010













































































































































































































Reviews:

No comments

Related manuals for JUNOS 10.1 - S 5-13-2010

Panasonic Avccam AG-AF100A Series Manual preview
Avccam AG-AF100A Series
Brand: Panasonic Pages: 19
IBM E02D1LL-E - Rational Rose Enterprise Installation Manual preview
E02D1LL-E - Rational Rose Enterprise
Brand: IBM Pages: 46
Paradyne OPENLANE User Manual preview
OPENLANE
Brand: Paradyne Pages: 86
Better Edge technology 5.2.7.0 User Manual preview
5.2.7.0
Brand: Better Edge technology Pages: 121
Siemens IEEE802.11 Tutorial preview
IEEE802.11
Brand: Siemens Pages: 84
Ulead VideoStudio 9 User Manual preview
VideoStudio 9
Brand: Ulead Pages: 218
Red Hat CERTIFICATE SYSTEM 8 - DEPLOYMENT Install Manual preview
CERTIFICATE SYSTEM 8 - DEPLOYMENT
Brand: Red Hat Pages: 132
AVG ANTI-VIRUS 8.5 User Manual preview
ANTI-VIRUS 8.5
Brand: AVG Pages: 234
Xerox 6100BD - Phaser Color Laser Printer User Manual preview
6100BD - Phaser Color Laser Printer
Brand: Xerox Pages: 56
MACROMEDIA FLASH 8-EXTENDING FLASH Manual preview
FLASH 8-EXTENDING FLASH
Brand: MACROMEDIA Pages: 554
McAfee VIRUSSCAN 5.1 User Manual preview
VIRUSSCAN 5.1
Brand: McAfee Pages: 315
Magellan eXplorist 210 Quick Reference Manual preview
eXplorist 210
Brand: Magellan Pages: 14
LapLink MN-LGD011-XX-US User Manual preview
MN-LGD011-XX-US
Brand: LapLink Pages: 166
Cisco CNS NetFlow Collection Engine Installation And Configuration Manual preview
CNS NetFlow Collection Engine
Brand: Cisco Pages: 36
MACROMEDIA ColdFusion MX Develop Manual preview
ColdFusion MX
Brand: MACROMEDIA Pages: 860
MACROMEDIA FLASH REMOTING MX Use Manual preview
FLASH REMOTING MX
Brand: MACROMEDIA Pages: 180
MACROMEDIA FLASH MEDIA SERVER 2 Reference preview
FLASH MEDIA SERVER 2
Brand: MACROMEDIA Pages: 234
MACROMEDIA FreeHand MX Use Manual preview
FreeHand MX
Brand: MACROMEDIA Pages: 412

Brands by name

Popular brands

Load more brands