Juniper JUNOS 10.1 - S 5-13-2010 Release Note Download Page 134 | Manualshive

Page: 134 / 204

background image

On SRX Series devices, the following IDP policies are supported:

■

DMZ_Services

■

DNS_Service

■

File_Server

■

Getting_Started

■

IDP_Default

■

Recommended

■

Web_Server

■

IDP deployed in both active/active and active/passive chassis clusters has the
following limitations:

■

No inspection of sessions that fail over or fail back.

■

The IP address action table is not synchronized across nodes.

■

The Routing Engine (RE) on the secondary node might not be able to reach
networks that are reachable only through a Packet Forwarding Engine (PFE).

■

The SSL session-ID cache is not synchronized across nodes. If an SSL session
reuses a session-ID and it happens to be processed on a node other than the
one on which the session-ID is cached, the SSL session cannot be decrypted
and will be bypassed for IDP inspection.

■

IDP deployed in active/active chassis clusters has the following limitation:

■

For time-binding scope source traffic, if attacks from a source with more
than one destination have active sessions distributed across nodes, the attack
might not be detected because time-binding counting has a local-node-only
view. Detecting this sort of attack requires an RTO synchronization of the
time-binding state that is not currently supported.

J-Web

■

On J Series devices, some J-Web pages for new features (for example, the Quick
Configuration page for the switching features on J Series devices) display content
in one or more modal pop-up windows. In the modal pop-up windows, you can
interact only with the content in the window and not with the rest of the J-Web
page. As a result, online Help is not available when modal pop-up windows are
displayed. You can access the online Help for a feature only by clicking the

Help

button on a J-Web page.

■

On SRX650 devices, you cannot use J-Web to configure a VLAN interface for an
IKE gateway. To configure a VLAN interface for an IKE gateway, use the CLI.

134

■

Known Limitations in JUNOS Release 10.1 for SRX Series Services Gateways and J Series Services Routers

JUNOS 10.1 Software Release Notes

«
...
132
133
134
135
136
...
»

Summary of Contents for JUNOS 10.1 - S 5-13-2010













































































































































































































Reviews:

No comments

Related manuals for JUNOS 10.1 - S 5-13-2010

Brand: Panasonic Pages: 20

Integrated Fiery Color Server

Brand: Xerox Pages: 24

DRAGON NATURALLYSPEAKING PROFESSIONAL 5

Brand: Dragon Systems Pages: 222

ANTI-VIRUS FOR MICROSOFT EXCHANGE 8.00 -

Brand: F-SECURE Pages: 29

SMROUTERUPDATINGFIRMWARE

Brand: Belkin Pages: 4

G2 PORTABLE HX-MU025DC

Brand: Samsung Pages: 1

Brand: Samsung Pages: 14

Brand: Steinberg Pages: 1

ITANIUM ARCHITECTURE

Brand: Intel Pages: 604

Brand: Fiery Pages: 214

Brand: Mad Catz Pages: 12

AUTOCAD PANDID 2011 - SYSTEM REQUIREMENTS

Brand: Autodesk Pages: 2

Brand: Autodesk Pages: 6

Brand: Autodesk Pages: 62

466B1-05A761-1304 - AutoCAD Inventor Simulation Suite 2010

Brand: Autodesk Pages: 84

22906-010000-9325 - UPG FROM AUTOCAD 2000I-NET BUMP

Brand: Autodesk Pages: 104

Brand: Daikin Pages: 16

Brand: Yamaha Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands