manualshive.com logo in svg

Juniper JUNOS 10.1 - S 5-13-2010, Release Note

The Juniper JUNOS 10.1 - S 5-13-2010 is a cutting-edge networking software, offering enhanced performance and security. Stay updated with the latest features and improvements by downloading the free Release Note manual from manualshive.com. Discover new possibilities and optimize your network effortlessly with this advanced product.

Share
Download
background image

■

On SRX Series devices, the 

show system storage partitions

 command now displays

the partitioning scheme details on SRX Series devices.

■

Example 1:

show system storage partitions (dual root partitioning)

user@host# 

show system storage partitions

Boot Media: internal (da0)
Active Partition: da0s2a
Backup Partition: da0s1a
Currently booted from: active (da0s2a)
Partitions Information:
Partition Size Mountpoint
s1a 293M altroot
s2a 293M /
s3e 24M /config
s3f 342M /var
s4a 30M recovery

■

Example 2:

show system storage partitions (single root partitioning)

user@host# 

show system storage partitions

Boot Media: internal (da0)
Partitions Information:
Partition Size Mountpoint
s1a 898M /
s1e 24M /config
s1f 61M /var
show system storage
partitions (USB)

■

Example 3:

show system storage partitions (usb)

user@host# 

show system storage partitions

Boot Media: usb (da1)
Active Partition: da1s1a
Backup Partition: da1s2a
Currently booted from: active (da1s1a)
Partitions Information:
Partition Size Mountpoint
s1a 293M /
s2a 293M altroot
s3e 24M /config
s3f 342M /var
s4a 30M recovery

Configuration

■

J Series devices no longer allow a configuration in which a tunnel's source or
destination address falls under the subnet of the same logical interface’s address.

122

■

Changes In Default Behavior and Syntax in JUNOS Release 10.1 for SRX Series Services Gateways and J Series Services

Routers

JUNOS 10.1 Software Release Notes

Summary of Contents for JUNOS 10.1 - S 5-13-2010













































































































































































































Reviews:

No comments

Related manuals for JUNOS 10.1 - S 5-13-2010

Canon imagePROGRAF W6400 Manual preview
imagePROGRAF W6400
Brand: Canon Pages: 84
F-SECURE ONLINE BACKUP - HELP Manual preview
ONLINE BACKUP - HELP
Brand: F-SECURE Pages: 20
MACROMEDIA ClusterCATS Use Manual preview
ClusterCATS
Brand: MACROMEDIA Pages: 156
MacroSystem Digital Video DVD-Arabesk 2 User Manual preview
DVD-Arabesk 2
Brand: MacroSystem Digital Video Pages: 28
Fujitsu Saving and Recovering Your Factory and System Images Manual preview
Saving and Recovering Your Factory and System Images
Brand: Fujitsu Pages: 16
Fujitsu Solaris 10 Hardware Platform Manual preview
Solaris 10
Brand: Fujitsu Pages: 52
Fujitsu Restoring Microsoft Windows® 7 Edition Manual preview
Restoring Microsoft Windows® 7 Edition
Brand: Fujitsu Pages: 4
Fujitsu ServerView Event Manager User Manual preview
ServerView Event Manager
Brand: Fujitsu Pages: 172
Fujitsu ScandAll PRO How To Use Manual preview
ScandAll PRO
Brand: Fujitsu Pages: 45
Fujitsu SOFTUNE User Manual preview
SOFTUNE
Brand: Fujitsu Pages: 234
Fujitsu ServerView Operations Manager V6.12 User Manual preview
ServerView Operations Manager V6.12
Brand: Fujitsu Pages: 282
Fujitsu ServerView Virtual-IO Manager V3.1 User Manual preview
ServerView Virtual-IO Manager V3.1
Brand: Fujitsu Pages: 362
Fujitsu ServerView Resource Orchestrator Cloud Edition V3.1.1 Operation User Manual preview
ServerView Resource Orchestrator Cloud Edition V3.1.1 Operation
Brand: Fujitsu Pages: 414
Fujitsu Remote Management User Manual preview
Remote Management
Brand: Fujitsu Pages: 426
Sawgrass Aficio GX7000 Getting Started Manual preview
Aficio GX7000
Brand: Sawgrass Pages: 48
Samsung UN55C7000WF Quick Setup Manual preview
UN55C7000WF
Brand: Samsung Pages: 2
Samsung UN40C7000WFXZA Troubleshooting Manual preview
UN40C7000WFXZA
Brand: Samsung Pages: 4
Samsung UN46ES8000FXZA Fast Track Troubleshooting preview
UN46ES8000FXZA
Brand: Samsung Pages: 5

Brands by name

Popular brands

Load more brands