manualshive.com logo in svg

Juniper JUNOS 10.1 - S 5-13-2010, Release Note

The Juniper JUNOS 10.1 - S 5-13-2010 is a cutting-edge networking software, offering enhanced performance and security. Stay updated with the latest features and improvements by downloading the free Release Note manual from manualshive.com. Discover new possibilities and optimize your network effortlessly with this advanced product.

Share
Download
background image

(and so on) is not supported. Use the offline procedures to upgrade and integrate
the remaining T1600 routers into the routing matrix.

[

TX Matrix Plus Hardware

, 

System Basics and Services Command Reference

]

■

Per-unit scheduling for GRE tunnels using IQ2 PICs (M7i, M10i, M120, and
M320 routers with E3–FPC)

—Supports enhanced IQ2 PIC and IQ2E PIC

performance, adding all functionality of tunnel PICs. The QoS for the GRE tunnel
traffic will be applied as the traffic is looped through the IQ2/IQ2E PIC.

Shaping is performed on full packets that pass through the GRE tunnel.

IQ2 and IQ2E PICs support all interfaces that are supported on tunnel PICs, as
follows:

■

gr-

fpc

/

pic

/

port

■

vt-

fpc

/

pic

/

port

■

lt-

fpc

/

pic

/

port

■

ip-

fpc

/

pic

/

port

■

pe-

fpc

/

pic

/

port

■

pd-

fpc

/

pic

/

port

■

mt-

fpc

/

pic

/

port

The port variable is always zero.

The provided tunnel functionality is the same as that of regular tunnel PICs.

When tunnel services are enabled on IQ2 and IQ2E PICs, they work exclusively
as tunnel PICs. The physical ports on the PICs cannot be used in tunnel mode.
To configure exclusive tunnel mode, use the 

tunnel-only

 statement at the 

[chassis

fpc number pic number]

 hierarchy level.

You can use the 

show interfaces queue gr-

fpc

/

pic

/

port

 command to display

statistics for the specified tunnel.

[

Network Interfaces

, 

Class of Service

, 

PIC Guide

]

■

Root System Domain (RSD) configuration of logical interface filters on shared
interfaces (JCS1200 platform)

—Enables Root System Domain (RSD) configuration

support for logical interface filters on shared interfaces. In previous releases,
logical interface filters were configured on each Protected System Domain (PSD).
This release supports configuration on the RSD.

To configure a logical interface filter on the RSD, apply the firewall filter to the
logical interface on the shared interface by including the 

filter output 

filter-name

statement at the 

[edit interfaces 

interface-name

 unit 

logical-unit-number

]

 hierarchy

level on the RSD.

Filtering is performed on the PSD, but logical interface filters configured on the
RSD are applied automatically by the PSD. Filters configured on the RSD can
co-exist with filters configured on the PSD. Counter statistics related to PSD
filtering are available on the RSD.

[

Protected System Domain

]

14

■

New Features in JUNOS Release 10.1 for M Series, MX Series, and T Series Routers

JUNOS 10.1 Software Release Notes

Summary of Contents for JUNOS 10.1 - S 5-13-2010













































































































































































































Reviews:

No comments

Related manuals for JUNOS 10.1 - S 5-13-2010

MACROMEDIA DREAMWEAVER 8-EXTENDING DREAMWEAVER Manual preview
DREAMWEAVER 8-EXTENDING DREAMWEAVER
Brand: MACROMEDIA Pages: 504
MACROMEDIA BREEZE 5 Integration Manual preview
BREEZE 5
Brand: MACROMEDIA Pages: 232
Adobe ILLUSTRATOR CS2 12.0.1 Manual preview
ILLUSTRATOR CS2 12.0.1
Brand: Adobe Pages: 6
Adobe 22011302 Manual preview
22011302
Brand: Adobe Pages: 8
Adobe 38043740 - ColdFusion Standard - Mac Manual preview
38043740 - ColdFusion Standard - Mac
Brand: Adobe Pages: 87
Adobe 38039927 - Fireworks CS3 - PC Using Instructions preview
38039927 - Fireworks CS3 - PC
Brand: Adobe Pages: 369
Adobe InDesign 2.0 Help Manual preview
InDesign 2.0
Brand: Adobe Pages: 478
Ulead GIF ANIMATOR 4.0 User Manual preview
GIF ANIMATOR 4.0
Brand: Ulead Pages: 64
Navman Smart V3 User Manual preview
Smart V3
Brand: Navman Pages: 53
Tektronix PhaserPrint 2.0 Configuration Manual preview
PhaserPrint 2.0
Brand: Tektronix Pages: 2
Z3 Technology Z3-DM8169-APP-L1-RPS User Manual preview
Z3-DM8169-APP-L1-RPS
Brand: Z3 Technology Pages: 46
UNIBLUE DRIVERSCANNER 2009 Manual preview
DRIVERSCANNER 2009
Brand: UNIBLUE Pages: 62
Ubiquiti airVision User Manual preview
airVision
Brand: Ubiquiti Pages: 38
DigiDesign Pro Tools M-Powered Basic Manual preview
Pro Tools M-Powered
Brand: DigiDesign Pages: 22
Valcom V-9923B User Manual preview
V-9923B
Brand: Valcom Pages: 8
IBM ZVSE ROADMAP Manual preview
ZVSE ROADMAP
Brand: IBM Pages: 38
Quantum Scalar 1000 Reference Manual preview
Scalar 1000
Brand: Quantum Pages: 304
Navman S-Series NavDesk 2009 User Manual preview
S-Series NavDesk 2009
Brand: Navman Pages: 36

Brands by name

Popular brands

Load more brands