manualshive.com logo in svg

Juniper JUNOS 10.1 - S 5-13-2010, Release Note

The Juniper JUNOS 10.1 - S 5-13-2010 is a cutting-edge networking software, offering enhanced performance and security. Stay updated with the latest features and improvements by downloading the free Release Note manual from manualshive.com. Discover new possibilities and optimize your network effortlessly with this advanced product.

Share
Download
background image

■

In the J-Web interface, the dashboard does not display the uplink ports when
transceivers are not plugged into the ports. [PR/477549]

■

An IPv4 static route configured using the CLI might not be displayed when you
select 

Configure -> Routing-> Static Routing

 in the J-Web interface. [PR/487597]

Related Topics

■

New Features in JUNOS Release 10.1 for EX Series Switches on page 184

■

Changes in Default Behavior and Syntax in JUNOS Release 10.1 for EX Series
Switches on page 187

■

Limitations in JUNOS Release 10.1 for EX Series Switches on page 188

■

Resolved Issues in JUNOS Release 10.1 for EX Series Switches on page 194

■

Errata in Documentation for JUNOS Release 10.1 for EX Series Switches on
page 198

■

Upgrade and Downgrade Issues for JUNOS Release 10.1 for EX Series Switches
on page 198

Resolved Issues in JUNOS Release 10.1 for EX Series Switches

The following are the issues that have been resolved since JUNOS Release 10.1R1
for EX Series switches. The identifier following the descriptions is the tracking number
in our bug database.

Access Control and Port Security

■

When both DHCP relay and DHCP snooping are configured on an EX2200 switch,
the DHCP snooping database might not be built on the switch. [PR/480682: This
issue has been resolved.]

Bridging, VLANs, and Spanning Trees

■

When Multiple VLAN Registration Protocol (MVRP) and MSTP are enabled together
on EX Series switches, convergence does not occur between MVRP and MSTP.
[PR/449248: This issue has been resolved.]

■

On EX4200 switches with the access interface through which traffic enters the
switch configured as trusted (

secure-access-port interface 

interface-name

dhcp-trusted

), VLAN Spanning Tree Protocol (VSTP) bridge protocol data units

(BPDUs) are sent to the Routing Engine with the learning CPU code 37 instead
of the reserved learning CPU code 306. [PR/468095: This issue has been resolved.]

■

On EX3200 and EX4200 switches with large VLAN configurations (more than
1024 VLANs), stale dynamic VLAN entries might be found in the Ethernet
switching process (

eswd

) after you delete VLANs or deactivate the Multiple VLAN

Registration Protocol (MVRP). [PR/471647: This issue has been resolved.]

■

On an EX2200 switch, when there is no spanning-tree protocol or redundant
trunk group configured in the network and there is traffic looping, after the
network loop is broken, sometimes MAC learning might not occur. As a

194

■

Resolved Issues in JUNOS Release 10.1 for EX Series Switches

JUNOS 10.1 Software Release Notes

Summary of Contents for JUNOS 10.1 - S 5-13-2010













































































































































































































Reviews:

No comments

Related manuals for JUNOS 10.1 - S 5-13-2010

Acer AO533 Driver Installation preview
AO533
Brand: Acer Pages: 4
R&S FSV-K7 Operating Manual preview
FSV-K7
Brand: R&S Pages: 262
Acer ASM Pro Installation Manual preview
ASM Pro
Brand: Acer Pages: 20
Acer eConsole User Manual preview
eConsole
Brand: Acer Pages: 33
Acer Destinator PN User Manual preview
Destinator PN
Brand: Acer Pages: 118
Lenovo Active Protection System Manual preview
Active Protection System
Brand: Lenovo Pages: 10
Lenovo Aptiva Hardware Maintenance Manual preview
Aptiva
Brand: Lenovo Pages: 464
Lenovo ACTIVATION Error Code List preview
ACTIVATION
Brand: Lenovo Pages: 3
Sawgrass Aficio GX7000 Getting Started Manual preview
Aficio GX7000
Brand: Sawgrass Pages: 48
CAKEWALK Cakewalk SONAR User Manual preview
Cakewalk SONAR
Brand: CAKEWALK Pages: 610
Red Hat CERTIFICATE SYSTEM 8 - DEPLOYMENT Install Manual preview
CERTIFICATE SYSTEM 8 - DEPLOYMENT
Brand: Red Hat Pages: 132
Red Hat CERTIFICATE SYSTEM 7.3 - ADMINISTRATION Administration Manual preview
CERTIFICATE SYSTEM 7.3 - ADMINISTRATION
Brand: Red Hat Pages: 554
AVG ANTI-VIRUS 9 FREE - REV 90.15 User Manual preview
ANTI-VIRUS 9 FREE - REV 90.15
Brand: AVG Pages: 146
TROY Group IRD 2300 Quick Start Manual preview
IRD 2300
Brand: TROY Group Pages: 10
Bay Networks Baystream 7 Notice preview
Baystream 7
Brand: Bay Networks Pages: 140
KAPERSKY ANTI-VIRUS 5.0 - FOR LOTUS NOTES-DOMINO User Manual preview
ANTI-VIRUS 5.0 - FOR LOTUS NOTES-DOMINO
Brand: KAPERSKY Pages: 137
Xerox 850DP - Phaser Color Solid Ink Printer Administrator'S Manual preview
850DP - Phaser Color Solid Ink Printer
Brand: Xerox Pages: 70
IBM BS029ML - WebSphere Portal Server Self Help Manual preview
BS029ML - WebSphere Portal Server
Brand: IBM Pages: 242

Brands by name

Popular brands

Load more brands