manualshive.com logo in svg

Juniper JUNOS 10.1 - S 5-13-2010, Release Note

The Juniper JUNOS 10.1 - S 5-13-2010 is a cutting-edge networking software, offering enhanced performance and security. Stay updated with the latest features and improvements by downloading the free Release Note manual from manualshive.com. Discover new possibilities and optimize your network effortlessly with this advanced product.

Share
Download
background image

The DOCSIS Mini-PIM is supported on the following SRX Series Services Gateways:

■

SRX210

■

SRX240

The DOCSIS Mini-PIM has the following key features:

■

Provides high data transfer rates of over 150 Mbps downstream

■

Supports four downstream and four upstream channel bonding

■

Supports quality of service (QoS)

■

Provides interoperability with any DOCSIS-compliant cable modem
termination system (CMTS)

■

Supports IPv6 and IPv4 for modem management interfaces

■

Supports Baseline Privacy Interface Plus (BPI+)

■

Supports Advanced Encryption Standard (AES)

[

JUNOS Software Security Configuration Guide

]

■

Very-high-bit-rate digital subscriber line (VDSL)

—VDSL technology is part of

the xDSL family of modem technologies that provide faster data transmission
over a single flat untwisted or twisted pair of copper wires.

The VDSL lines connect service provider networks and customer sites to provide
high bandwidth applications (Triple Play services) such as high-speed Internet
access, telephone services like voice over IP (VoIP), high-definition TV (HDTV),
and interactive gaming services over a single connection. VDSL2 is an
enhancement to VDSL and permits the transmission of asymmetric and
symmetric (full-duplex) aggregate data rates up to 100 Mbps on short copper
loops using a bandwidth up to 30 MHz. The VDSL2 technology is based on the
ITU-T G.993.2 standard.

The following SRX Series Services Gateways support the VDSL2 Mini-Physical
Interface Module (Mini-PIM) (Annex A):

■

SRX210 Services Gateway

■

SRX240 Services Gateway

The VDSL2 Mini-PIM carries the Ethernet backplane. When the Mini-PIM is
plugged into the chassis, the Mini-PIM connects to one of the ports of the
baseboard switch.

The VDSL2 Mini-PIM supports following features:

■

ADSL/ADSL2/ADSL2+ backward compatibility with Annex-A, Annex-M
Support

■

PTM or EFM [802.3ah] support

■

Operation, Administration, and Maintenance (OAM) support for
ADSL/ADSL/ADSL2+ ATM mode

New Features in JUNOS Release 10.1 for SRX Series Services Gateways and J Series Services Routers

■

103

New Features in JUNOS Release 10.1 for SRX Series Services Gateways and J Series Services Routers

Summary of Contents for JUNOS 10.1 - S 5-13-2010













































































































































































































Reviews:

No comments

Related manuals for JUNOS 10.1 - S 5-13-2010

XenSource DL385 - ProLiant - G5 Manual preview
DL385 - ProLiant - G5
Brand: XenSource Pages: 313
Juniper RESIDENT CONSULTANT Datasheet preview
RESIDENT CONSULTANT
Brand: Juniper Pages: 4
TC Electronic Tap Factory Product Manual preview
Tap Factory
Brand: TC Electronic Pages: 12
Belkin UPGRADE FIRMWARE MODEM ROUTER Manual preview
UPGRADE FIRMWARE MODEM ROUTER
Brand: Belkin Pages: 1
Fargo Persona Persona M30e User Manual preview
Persona Persona M30e
Brand: Fargo Pages: 31
Toshiba HDWC110XK3J1 Quick Start preview
HDWC110XK3J1
Brand: Toshiba Pages: 1
Toshiba dynadock Drivers Update preview
dynadock Drivers
Brand: Toshiba Pages: 3
Toshiba e-STUDIO Printer/Fax/Scanner/Copier Brochure preview
e-STUDIO Printer/Fax/Scanner/Copier
Brand: Toshiba Pages: 4
Toshiba 6F3A4508 Instruction Manual preview
6F3A4508
Brand: Toshiba Pages: 53
Quantum PX500 Series Installation Instructions Manual preview
PX500 Series
Brand: Quantum Pages: 26
Quantum Management Console 4.4 User Manual preview
Management Console 4.4
Brand: Quantum Pages: 120
LinPlug MorphoX User Manual preview
MorphoX
Brand: LinPlug Pages: 46
AVG ANTI-VIRUS 2011 - REV 2011.03 User Manual preview
ANTI-VIRUS 2011 - REV 2011.03
Brand: AVG Pages: 211
MACROMEDIA DREAMWEAVER 8-GETTING STARTED WITH... Getting Started preview
DREAMWEAVER 8-GETTING STARTED WITH...
Brand: MACROMEDIA Pages: 326
Native Instruments Reaktor Prism Manual preview
Reaktor Prism
Brand: Native Instruments Pages: 58
KAPERSKY SECURITY 5.5 - FOR PDA User Manual preview
SECURITY 5.5 - FOR PDA
Brand: KAPERSKY Pages: 66
Asus Security Protect Manager User Manual preview
Security Protect Manager
Brand: Asus Pages: 14
Lenovo ThinkStation D20 Safety And Warranty Manual preview
ThinkStation D20
Brand: Lenovo Pages: 272

Brands by name

Popular brands

Load more brands