Juniper JUNOS 10.1 - S 5-13-2010 Release Note Download Page 183

Page: 183 / 204

■

installMedia

—Refers to the installation media downloaded into the

/var/tmp

directory. For example,

install-media-srx5000-10.1R1-domestic.tgz

The following code example can be used to write the image that you copied to
the master Routing Engine (RE0) in step 1 onto the USB storage device:

dd if=install-media-srx5000-10.1R1-domestic.tgz of=/dev/da0 bs=64k

Log out as root or superuser:

exit

After the software image is written to the USB storage device, remove the device
and insert it into the USB port on the second Routing Engine (RE1).

Move the console connection from the master Routing Engine (RE0) to the second
Routing Engine (RE1), if you do not already have a connection.

Reboot the second Routing Engine (RE1). Issue the following command:

# reboot

■

When the following system output appears, press

WARNING: The installation will erase the contents of your disks.
Do you wish to continue (y/n)?

■

When the following system output appears, remove the USB storage device
and press

Enter

Eject the installation media and hit [Enter] to reboot?

Upgrade and Downgrade Instructions for JUNOS Release 10.1 for SRX Series Services
Gateways and J Series Services Routers

In order to upgrade to JUNOS Release 10.1 or later, your device must be running
one of the following JUNOS Software releases:

■

9.1S1

■

9.2R4

■

9.3R3

■

9.4R3

■

9.5R1 or later

If your device is running an earlier release, upgrade to one of these releases and then
to the 10.1 release. For example, to upgrade from Release 9.2R1, first upgrade to
Release 9.2R4 and then to Release 10.1R2.

Upgrade and Downgrade Instructions for JUNOS Release 10.1 for SRX Series Services Gateways and J Series Services

Routers

■

183

Upgrade and Downgrade Instructions for JUNOS Release 10.1 for SRX Series Services Gateways and J Series Services Routers

Summary of Contents for JUNOS 10.1 - S 5-13-2010













































































































































































































Search results

Summary of Contents for JUNOS 10.1 - S 5-13-2010

Reviews:

Related manuals for JUNOS 10.1 - S 5-13-2010

Brands by name

Popular brands

Juniper JUNOS 10.1 - S 5-13-2010, Release Note

Search results

Summary of Contents for JUNOS 10.1 - S 5-13-2010

Reviews:

Related manuals for JUNOS 10.1 - S 5-13-2010

Brands by name

Popular brands