JUKI LBH-1700, Engineer'S Manual

Page: 58 / 126

−
54
−
(1) Sewing data
1) Make sure that sewing LED
1
goes off.
(When it lights up, press [Ready] key
2
to make
the LED go off.)
2) Press [Pattern No.] key
3
to display the pattern
No. (It is not necessary when the pattern is not
changed.)
3) Press [Left ] key
4
or [Left ] key
5
to select the
pattern No. you desire to change. (It is not necessary
when the pattern is not changed.)
4) Press [Data] key
6
to display the data No.
5) Press [Left ] key
4
or [Left ] key
5
to select the
data No. you desire to change.
6) Press [Right ] key
7
or [Right ] key
8
to change
the data.
7) Repeat steps 5), and 6) and when setting is completed,
press [Ready] key
2
to light up sewing LED.
(When turning OFF the power without pressing
[Ready] key
2
, the data is not stored in memory.
Then, it is necessary to re-enter.)
(2) Sewing data list
PATTERN DATA COUNTER TENSION
WIDTH
PITCH
LENGTH
– +
CLEARANCE
KNIFE
FEED
LEFT/CLEARANCE/RIGHT
LEFT/BARTACK/RIGHT
READY RESET CLAMP WINDER THREAD
1
2
3
4
5
6
7
8
7 : Bar-tacking
No.
1
2
3
4
5
6
7
8
9
10
11
12
Description
This item sets length of cloth that is cut by cloth cutting knife.
When knife performs plural motions, plural motions are performed in accordance
with knife size which has been set, and the cloth is cut as much as the set value.
Normally, knife length is set for the knife drop of one time.
(Setting more than 3 types of presser size is treated as the special order.)
This item sets the clearance between cloth cutting knife and right parallel section.
This item sets the clearance between cloth cutting knife and left parallel section.
This item sets stitch width of left parallel section.
This item sets length of 2nd bar-tacking section.
Square type, radial square type, radial taper bar, radial straight bar, eyelet square
type, eyelet flow bar-tacking, eyelet straight bar-tacking : 2nd bar-tacking setting
This item sets the clearance between 1st bar-tacking and knife groove.
This item sets the clearance between 2nd bar-tacking and knife groove.
Sewing machine performs jump feed after stopping and knife operates depending on
the set value.
This item sets sewing pitch of left and right parallel sections.
This item sets sewing pitch of bar-tacking section.
This item selects the shape.
This item sets length of bar-tacking section.
Radial square type, round square type, radial taper bar, radial straight bar :
1st bar-tacking setting
Radial, round type, semilunar type : Common setting to 1st abd 2nd bar-tacking.
Eyelet radial type : 2nd bar-tacking setting
This item sets number of stitches of radial shape section.
Setting range
6.0 to 67.0
0 to 2.0
0 to 2.0
0.1 to 3.0
0.2 to 5.0
0 to 4.0
0 to 4.0
0.20 to 2.5
0.20 to 2.5
0/1/2/3/4/5/6/7/8/9/
10/11/12
1.0 to 5.0
1 to 4
Unit
0.1 mm
0.05 mm
0.05 mm
0.05 mm
0.1 mm
0.1 mm
0.1 mm
0.05 mm
0.05 mm
1
0.1 mm
1N
Setting item
Cloth cut length
Knife groove width, right
Knife groove width, left
Stitch width, left
2nd bar-tacking length
1st clearance
2nd clearance
Pitch at pararell section
Pitch at bar-tacking section
Shape
Length of radial round type shape
Number of stitches of radial shape
0 : Square
type 1 : Radial
type 2 : Radial square
type 3 : Round
type
4 : Round
square
type
5 : Radial
taper
bar
6 : Radial
straight
bar
8 : Semilunar
type
9 : Eyelet
square type
10 : Eyelet
radial type
11 : Eyelet flow bar-
tacking type
12 : Eyelet straight bar-
tacking type
＊
3
＊ 5
1 2 3 4