JLG 1850SJ, Service And Maintenance Manual, Page: 118 / 712

SECTION 3 - CHASSIS & TURNTABLE
3-68 3121619
140 767 523941 9 Timeout Error (BAM to packet) for CAN-
Receive-Frame AT1OGCVol2 information;
factors & Sensorcalibration for NOX Sensor
(SCR-system downstream cat; DPF-system
downstream cat) Timeout Error (Missing CAN Bus message) NOX downstream sensor and sensor connection
check
141 767 523942 9 Timeout Error (BAM to BAM) for CAN-
Receive-Frame AT1OGCVol2 information,
Calibration message 1 of the after catalyst
NOx sensor has failed.
Factors & Sensorcalibration for NOX Sensor
(SCR-system downstream cat, DPF-system
downstream cat) Defective Nox sensor, faulty parameterization. NOX downstream sensor and sensor connection
check.
142 767 523943 9 Timeout Error (PCK2PCK) for CAN-Receive-
Frame AT1OGCVol2 information; factors &
Sensorcalibration for NOX Sensor (SCR-sys-
tem downstream cat; DPF-system
downstream cat) The fault is detected when a timeout error in
packet 2 of NOxSenVol2Rx frame occurs. NOX downstream sensor and sensor connection
check
168 763 523935 12 Timeout Error of CAN-Transmit-Frame
EEC3VOL1; Engine send messages Fault is detected if a TimeOut of the EEC3VOL1
frame has occured. Check wiring harness and customer nodes
169 764 523936 12 Timeout Error of CAN-Transmit-Frame
EEC3VOL2; Engine send messages Timeout Error (Missing CAN Bus message) Check wiring harness and customer nodes
171 3-3-3 523212 9 Timeout Error of CAN-Receive-Frame
ComEngPrt; Engine Protection Timeout Error (Missing CAN Bus message) Check wiring harness and customer devices
179 527 523240 9 Timeout CAN-message FunModCtl; Func-
tion Mode Control Timeout Error (Missing CAN Bus message) Check CAN Bus cabling (Bus sheduling, polarity,
short circuit, power interrupt), test
protocol of receiver, check CAN functional
range.
291 119 523776 9 Timeout Error of CAN-Receive-Frame TSC1TE
- active Timeout Error (Missing CAN Bus message) Threshold for error detection is an internal ECU
threshold.
Check CAN Bus cabling (Bus sheduling, polarity,
short circuit, power interrupt), test
protocol of receiver, check CAN functional
range.
292 119 523777 9 Message TSC1-TE has been missing (passive) Passive timeout Error (Missing CAN Bus mes-
sage)
Check CAN Bus cabling (Bus scheduling, polar-
ity, short circuit, power interrupt), test
protocol of receiver, check CAN functional
range, check actuator
305 118 898 9 Timeout Error of CAN-Receive-Frame TSC1TE
- active Timeout Error (Missing CAN Bus message) Check CAN Bus cabling (Bus sheduling, polarity,
short circuit, power interrupt), test
protocol of receiver, check CAN functional
range.
360 737 523982 0 Powerstage diagnosis disabled; Indicating
that battery voltage is not high. Powerstage diagnostic can be deactivated due
to too high battery voltage. Check wiring, check alternator, check cables and
repair or replace if necessary.
361 737 523982 1 Powerstage diagnosis disabled; Indicating
that battery voltage is not low. Powerstage diagnostic can be deactivated due
to too low battery voltage. Check wiring, check alternator, check cables and
repair or replace if necessary.
Table 3-10. Engine Fault Codes
Deutz
Code
Blink
Code
SPN FMI Description Possible Cause Action