Jeep 2008 Liberty Owner'S Manual Download Page 69 | Manualshive

Page: 69 / 493

Jeep 2008 Liberty Owner'S Manual Download Page 69

Data Parameters that May Be Recorded:

•

Diagnostic trouble code(s) and warning light status for
electronically controlled safety systems, including the
airbag system

•

Airbag disable light status (if equipped)

•

9

Time

9

of airbag deployment (in terms of ignition

cycles and vehicle mileage)

•

Airbag deployment level (if applicable)

•

Impact acceleration and angle

•

Seat belt status

•

Brake status (service and parking brakes)

•

Accelerator status (including vehicle speed)

•

Engine control status (including engine speed)

•

Transmission gear selection

•

Cruise control status

•

Traction/stability control status

•

Tire pressure monitoring system status

Child Restraint

Everyone in your vehicle needs to be buckled up all the
time — babies and children, too. Every state in the United
States and all Canadian provinces require that small
children ride in proper restraint systems. This is the law,
and you can be prosecuted for ignoring it.

Children 12 years and under should ride properly buck-
led up in a rear seat, if available. According to crash
statistics, children are safer when properly restrained in
the rear seats rather than in the front.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

69

2

«
...
67
68
69
70
71
...
»

Summary of Contents for 2008 Liberty














































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands