manualshive.com logo in svg

Jeep 2008 Liberty, Owner'S Manual

Share
Download
Jeep 2008 Liberty Owner'S Manual Download Page 149

To Resume Speed:

If you deactivated the speed control without erasing the
set speed from memory and your vehicle speed is above
20 mph (32 km/h) you can resume the previous set
speed. To do so, push the lever up and release (RESUME
ACCEL), and then remove your foot from the accelerator
pedal.

To Vary The Speed Setting:

When the speed control is set, you can increase speed by
pushing up and holding the lever (“RESUME ACCEL”).
Release the lever when the desired speed is reached, and
the new set speed will be established.

Tapping (“RESUME ACCEL”) once will result in a 1 mph
(2 km/h) speed increase. Each time the lever is tapped,
speed increases so that tapping the lever three times will
increase speed by 3 mph (5 km/h), etc.

To decrease speed while the speed control is set, push
down and hold the lever (“SET DECEL”). Release the
lever when the desired speed is reached, and the new set
speed will be established.

Tapping the (“SET DECEL”) button once will result in a
1 mph (2 km/h) speed decrease. Each time the button is
tapped, speed decreases.

To Accelerate For Passing

Depress the accelerator as you would normally. When the
pedal is released, the vehicle will return to the set speed.

Using Speed Control On Hills

NOTE:

The speed control system maintains speed up

and down hills. A slight speed change on moderate hills
is normal.

On steep hills, a greater speed loss or gain may occur so
it may be preferable to drive without speed control.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

149

3

Summary of Contents for 2008 Liberty














































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands