Jeep 2008 Liberty Owner'S Manual Download Page 25 | Manualshive

Page: 25 / 493

Jeep 2008 Liberty Owner'S Manual Download Page 25

headlights and turn signal lights will flash, the horn will
pulse on and off, and the illuminated entry system will
turn on.

The panic alarm will stay on for 3 minutes unless you
turn it off by pressing the Panic button a second time or
if the vehicle speed is 5 mph (8 km/h) or greater.

During the Panic Mode, the door locks and remote
keyless entry system will function normally. Panic mode
will not disarm the security system on vehicles so
equipped.

NOTE:

You may need to be close to the vehicle when

using the transmitter to turn off the panic alarm due to
the radio frequency noises emitted by the system.

Programming Additional Transmitters

Refer to SENTRY KEY “Customer Key Programming.”
in this section.

NOTE:

If you do not have a programmed transmitter,

contact your dealer for details.

Battery Replacement

The recommended replacement battery is CR2032.

NOTE:

•

Perchlorate Material — special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate.

•

Do not touch the battery terminals that are on the back
housing or the printed circuit board.

1. Remove the screw from the transmitter case (if
equipped).

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

25

2

«
...
23
24
25
26
27
...
»

Summary of Contents for 2008 Liberty














































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands