Jeep 2008 Liberty Owner'S Manual Download Page 167

Page: 167 / 493

NOTE:

The Sky Slider

will not open from the front and

the rear at the same time. The Sky Slider

must close fully

before opening it from the opposite end.

Using Operator Mode
Press the switch rearward and hold it and the Sky Slider

will open from the front and move toward the rear of the
vehicle.

Press the switch forward and hold it and the Sky Slider

will open from the rear and move toward the front of the
vehicle.

For either operation, the Sky Slider

will open fully and

stop automatically unless you interrupt the operation by
releasing the switch.

To resume the operation from a partially open position,
press and hold the switch once again.

NOTE:

The Sky Slider

will not open from the front and

the rear at the same time. The Sky Slider

must close fully

before opening it from the opposite end.

Closing the Sky Slider

Using Automatic Mode
Press and release the button in the center of the switch
and the Sky Slider

will close automatically from any

position. The Sky Slider

will close fully and stop auto-

matically.

Using Operator Mode
Press the switch rearward and hold it and the Sky Slider

will move forward.

Press the switch forward and hold it and the Sky Slider

will move rearward.

For either operation, the Sky Slider

will close fully and

stop automatically unless you interrupt the operation by
releasing the switch.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

167

Summary of Contents for 2008 Liberty














































































































































































































































































































































































































































































































Search results

Summary of Contents for 2008 Liberty

Reviews:

Brands by name

Popular brands

Jeep 2008 Liberty, Owner'S Manual

Search results

Summary of Contents for 2008 Liberty

Reviews:

Brands by name

Popular brands