manualshive.com logo in svg

Jeep 2008 Liberty, Owner'S Manual

Share
Download
Jeep 2008 Liberty Owner'S Manual Download Page 147

ELECTRONIC SPEED CONTROL — IF EQUIPPED

When engaged, this device takes over the accelerator
operation at speeds greater than 25 mph (40 km/h).

Electronic Speed Control Operation

The speed control lever is located on the right side of the
steering wheel.

To Activate:

Push and release the (“ON/OFF”) button lo-
cated on the end of the speed control lever. The
CRUISE indicator in the instrument cluster will
illuminate. To turn the system OFF, push and

release the (“ON/OFF”) button a second time. The
CRUISE indicator will turn off. Be sure to turn the system
OFF when not in use.

NOTE:

•

The Electronic Speed Control System will automati-
cally turn off when the engine is turned off.

•

The Electronic Speed Control System is designed to
shut down if you operate multiple speed control
switch-functions simultaneously (i.e. SET and CAN-
CEL). If this occurs, push and release the (“ON/OFF”)
button to reactivate the system and then reestablish
the desired SET speed.

Speed Control Lever

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

147

3

Summary of Contents for 2008 Liberty














































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands