manualshive.com logo in svg

Jeep 2008 Liberty, Owner'S Manual

Share
Download
Jeep 2008 Liberty Owner'S Manual Download Page 414

Operation of the wipers on dry glass for long periods
may cause deterioration of the wiper blades. Always use
washer fluid when using the wipers to remove salt or dirt
from a dry windshield.

Avoid using the wiper blades to remove frost or ice from
the windshield. Make sure that they are not frozen to the
glass before turning them on to avoid damaging the
blade.

Keep the blade rubber out of contact with petroleum
products such as engine oil, gasoline, etc.

NOTE:

Always refer to the wiper blade packaging for

specific installation instructions. Many wiper blade re-
placements fit multiple vehicles.

Windshield & Rear Window Washers

The windshield and rear window washers share the same
fluid reservoir. The fluid reservoir is located in the front
of the engine compartment. Be sure to check the fluid
level in the reservoir at regular intervals. Fill the reservoir
with windshield washer solvent (not radiator antifreeze)
and operate the system for a few seconds to flush out the
residual water.

When refilling the washer fluid reservoir, take some
washer fluid and apply it to a cloth or towel and wipe
clean the wiper blades, this will help blade performance.

To prevent freeze-up of your windshield washer system
in cold weather, select a solution or mixture that meets or
exceeds the temperature range of your climate. This
rating information can be found on most washer fluid
containers.

414

MAINTAINING YOUR VEHICLE

Summary of Contents for 2008 Liberty














































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands