manualshive.com logo in svg

Jeep 2008 Liberty, Owner'S Manual

Share
Download
Jeep 2008 Liberty Owner'S Manual Download Page 277

STARTING PROCEDURES

Before starting your vehicle, adjust your seat, adjust both
inside and outside mirrors, and fasten your seat belts.

WARNING!

Do not leave children or animals inside parked
vehicles in hot weather. Interior heat build up may
cause serious injury or death.

Automatic Transmission

Start the engine with the selector lever in the “N”
(Neutral) or “P” (Park) position. Apply the brake before
shifting to any driving range.

Manual Transmission — If Equipped

Apply the parking brake, place the gearshift control lever
in “N” (Neutral) and depress the clutch pedal before

starting vehicle. This vehicle is equipped with a clutch
interlocking ignition system. It will not start unless the
clutch pedal is pressed to the floor.

4WD Models Only
To enhance off-road performance, 4-wheel drive models
equipped with a manual transmission will start with or
without pressing the clutch pedal when in 4-wheel drive
low range. The 4 LOW indicator light will illuminate
when the transfer case is in 4-wheel drive low range.

Normal Starting

NOTE:

Normal starting of either a cold or a warm

engine is obtained without pumping or depressing the
accelerator pedal.

For vehicles not equipped with Tip Start,

turn the ignition

switch to the START position and release it when the
engine starts. If the engine fails to start within 10 seconds,
turn the ignition switch to the LOCK position, wait 10 to
15 seconds, then repeat the normal starting procedure.

STARTING AND OPERATING

277

5

Summary of Contents for 2008 Liberty














































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands