manualshive.com logo in svg

Jeep 2008 Liberty, Owner'S Manual

Share
Download
Jeep 2008 Liberty Owner'S Manual Download Page 445

Front Fog Light

1. Open the hood.

2. Reach behind the headlight housing to access the bulb.

3. Rotate the bulb’s socket counterclockwise, and remove
the bulb and socket assembly from the fog light housing.

4. Pull the bulb out of the socket and insert the replace-
ment bulb.

CAUTION!

Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with any oily surface, clean the
bulb with rubbing alcohol.

5. Install the bulb and socket assembly into the into the
fog light housing, and rotate the connector clockwise to
lock it in place.

6. Close the hood.

Rear Tail/Stop, Turn Signal, and Back-Up Lights

1. Open the liftgate.

2. Remove the screws that fasten the taillight housing to
the vehicle.

3. Pull the taillight housing straight back to separate it
from the vehicle.

4. Disconnect the electrical connector.

MAINTAINING YOUR VEHICLE

445

7

Summary of Contents for 2008 Liberty














































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands