manualshive.com logo in svg

Jeep 2008 Liberty, Owner'S Manual

Share
Download
Jeep 2008 Liberty Owner'S Manual Download Page 166

Power Top Control

The Power Top switch is located between the sun visors
on the overhead console.

NOTE:

The Power Top switch will operate when the

ignition switch is turned to the ON or ACC position, and
when the accessory delay feature is active.

Opening the Sky Slider

T

Using Automatic Mode
Press the switch rearward and release it within

1

⁄

2

second

and the Sky Slider

t

will open from the front and move

automatically toward the rear of the vehicle.

Press the switch forward and release it within

1

⁄

2

second

and the Sky Slider

t

will open from the rear and move

automatically toward the front of the vehicle.

For either operation, the Sky Slider

t

will open fully and

stop automatically unless you interrupt the operation by
pressing and releasing the switch again.

NOTE:

You can press the switch in either direction to

interrupt the operation.

To resume the operation from a partially open position,
press and release the switch once again.

Power Top Switch

166

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for 2008 Liberty














































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands