manualshive.com logo in svg

Jeep 2008 Liberty, Owner'S Manual

Share
Download
Jeep 2008 Liberty Owner'S Manual Download Page 315

Two additional electronic brake control system options
are HDC (Hill Descent Control) and TSC (Trailer Sway
Control). Your vehicle may be equipped with one or both
of these options.

ABS (Anti-Lock Brake System)

This system aids the driver in maintaining vehicle control
under adverse braking conditions. The system controls
hydraulic brake pressure to prevent wheel lock-up to
help avoid skidding on slippery surfaces during braking.
Refer to “Anti-Lock Brake System” in Section 5 of this
manual for more information about ABS.

WARNING!

ABS (Anti-Lock Brake System) cannot prevent the
natural laws of physics from acting on the vehicle,
nor can it increase the traction afforded by prevailing
road conditions. ABS cannot prevent accidents, in-
cluding those resulting from excessive speed in
turns, driving on very slippery surfaces, or hydro-
planing. Only a safe, attentive, and skillful driver can
prevent accidents. The capabilities of an ABS-
equipped vehicle must never be exploited in a reck-
less or dangerous manner, which could jeopardize
the user’s safety or the safety of others.

STARTING AND OPERATING

315

5

Summary of Contents for 2008 Liberty














































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands