Jeep 2008 Liberty Owner'S Manual Download Page 40 | Manualshive

Page: 40 / 493

Jeep 2008 Liberty Owner'S Manual Download Page 40

LIFTGATE

To open the liftgate, pull up (squeeze) on the handle and
lift.

NOTE:

Use the power door lock switch on either front

door trim panel or the Remote Keyless Entry (RKE)
transmitter to lock and unlock the liftgate. The manual
door locks on the doors and the driver’s door lock
cylinder will not lock and unlock the liftgate.

WARNING!

Driving with the liftgate open can allow poisonous
exhaust gases into your vehicle. You and your pas-
sengers could be injured by these fumes. Keep the
liftgate closed when you are operating the vehicle.

Liftgate Release

40

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
38
39
40
41
42
...
»

Summary of Contents for 2008 Liberty














































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands