![background image](http://html1.mh-extra.com/html/jcm-global/uba-rc-series/uba-rc-series_operation-and-maintenance-manual_3545425049.webp)
P/N 960-100928R_Rev. 3 {EDP #192692}
© 2018, JAPAN CASH MACHINE CO., LTD.
4 - 5
Disassembly/Reassembly
UBA-RC™ Series Banknote Recycler
Section 4
e
) in place, and separate the Frame Guide 3
from the Right Frame.
3. Remove the six (6) Sensor Covers (Figure 4-14
a
1
to
a
6
) and remove the Upper & Lower Full Sensor
LEDs (Figure 4-14
b
&
c
), the Upper & Lower
End Sensor PTs (Figure 4-14
d
&
e
) and the Lifter
Home Position Sensor LED (Figure 4-14
f
) and
the Lifter Home Position Sensor PT (Figure 4-14
g
) located on Frame Guide 3; then unplug the six
(6) related Signal Connectors (Figure 4-14
h
1
to
h
6
) from each Sensor.
Upper & Lower Flapper Pusher
Lever Solenoid Removal
To remove the Flapper Pusher Lever Solenoid,
proceed as follows:
1. Pull the Harness (Figure 4-15
a
) to the back side
of the Rear Transport Assembly (Figure 4-15
b
).
2. Remove the six (6) Mounting Screws (Figure 4-
c
1
to
c
6
) retaining the Upper Flapper Pusher
Lever Solenoid (Figure 4-15
d
) and the Lower
Flapper Pusher Lever Solenoid in place (Figure 4-
e
); then remove both the Upper and Lower
Flapper Lever Solenoids from the Rear Transport
Assembly.
Flapper Open/Close Circuit
Board Removal
To remove the Flapper Open/Close Circuit Board,
proceed as follows:
1. Remove the two (2) E-Rings (Figure 4-16
a
1
&
a
2
) retaining the two (2) Flapper Pusher Brackets
b
1
&
b
2
) in place, and remove the
Flapper Pusher Brackets from the Rear Transport
Assembly (Figure 4-16
c
).
2. Remove the two (2) Mounting Screws (Figure 4-
e
1
&
e
2
) retaining the Flapper Open/Close Cir-
cuit Boards (Figure 4-16
f
1
&
f
2
) in place, and
unplug each of their related Signal Connectors
g
1
&
g
2
); then remove the two (2)
Flapper Open/Close Circuit Boards from the Rear
Transport Assembly.
Full Sensor LEDs, End Sensor PTs
and Lifter Home Position Sensor LED/PT
Removal
a
1
a
2
a
3
a
4
a
5
a
6
b
c
d
e
f
g
h
3
h
4
h
5
h
6
Figure 4-14
Full Sensor LEDs, End Sensor PTs
and Lifter Home Position Sensor
LED/PT Removal
NOTE: When re-assembling both
the Upper and Lower Flapper
Solenoids, pull upward in the
direction of the Red Arrow indicated
in the Figure 4-15
f
inset, and then
replace their related carrier with their
mounting screws.
Figure 4-15
d
e
a
c
1
c
2
c
3
c
4
c
5
c
6
b
f
d&e
Figure 4-15
Upper & Lower Flapper Pusher
Lever Solenoid Removal
NOTE: Before removing the Flapper
Pusher Brackets, remove the two (2)
Springs (Figure 4-16
d
1
&
d
2
) from
the Rear Transport Assy.