![background image](http://html1.mh-extra.com/html/jcm-global/uba-rc-series/uba-rc-series_operation-and-maintenance-manual_3545425017.webp)
P/N 960-100928R_Rev. 3 {EDP #192692}
© 2018, JAPAN CASH MACHINE CO., LTD.
1 - 3
General Information
UBA-RC™ Series Banknote Recycler
Section 1
User Cautions
Careful measures are taken in the design of this
product to ensure its quality; however, the follow-
ing cautions should be read and understood by all
users in order to confirm safe operation.
I
NSTALLATION
C
AUTIONS
The Installation Cautions are defined as follows:
1. Do not allow the Unit to endure or operate at a
high temperature, in high humidity and/or in a
dusty environment.
2. Do not install the Unit into an area where exces-
sive vibration or shock are present.
3. The Unit is not designed for outside installation.
Be sure that the Host Machine contains enough
protection to avoid wet or dusty conditions when
installing in either an indoor or open-air space.
4. Avoid exposing the Unit to direct Sunlight and/or
Incandescent Lamp illumination having a
Gradient Angle of 15 Degree or more, and an
illumination index of 3000 Lux or less.
5. Ensure that the Host Machine is designed for
daily operational access for maintenance
and/or clearing a Banknote jam.
6. When
installing
the
equipment, connect the
Frame Housing to the Frame Ground of the Host
Machine.
7. If an unused Interface Harness exists, cut the
Harness off short to avoid attracting static elec-
tricity or a short circuit possibility that may cause
damage to the Unit.
8. Because this equipment is a component product,
close the Host Machine’s door before using it.
9. Do not operate the
UBA-RC
™
Unit while the
Cash Box and/or the Recycler Unit’s door is open.
Personal injury may occur.
10. This Unit is designed to use a current limiting
Power Source. Be sure that the Host Machine’s
cabinet material design meets local safety stan-
dards.
M
OUNTING
, D
ISMOUNTING
& T
RANSPORTATION
Methods for Mounting, Dismounting, and Trans-
porting the Unit are as follows:
1. Be sure to turn the Power OFF to the UBA-RC
™
Unit before mounting or removing the Recycler
Unit from its permanent location. Attaching or
unplugging Connector Plugs from their Recepta-
cles while the Power is ON may damage the Unit.
2. When reassembling a Unit’s Section, ensure that
each part is replaced in its correct location.
3. Be sure to carry the Unit by both hands when
transporting it. Holding the Unit by one hand may
cause personal injury if the Unit accidentally
becomes disassembled and falls away from the
Frame housing.
4. Be careful not to use excessive outside pressure
on the Recycler Unit, or subject it to excessive
vibration during transportation.
5. Check that the UBA
™
Transport Section does not
drop off the Unit Frame while pulling the Recy-
cler forward from the Frame.
Preventive Maintenance
The Preventive Maintenance requirements are
defined as follows:
1. Be sure to turn the Power OFF before beginning a
maintenance procedure. The equipment produces
improper operating signals while in maintenance
mode that may cause personal injury.
2. When closing the Recycler Unit, ensure all ser-
vice door locks click into place.
3. If the UBA
™
Validator Section is dirty due to dust,
foreign objects or other such debris adhering to it,
the Banknote acceptance rate will degrade. Clean
the Transport Unit once a month to keep its per-
formance stable.
4. Use a soft, lint-free cloth, cotton swab or a com-
pressed air spray to clean dust and debris from the
Banknote path and the inside areas of the
Recycler.
5. Do not redesign or disassemble the Recycler Unit.
Unauthorized use by inadequately-trained
personnel, or use outside the original manufac-
turer’s intent for operation voids the warranty.
Caution: DO NOT use any alcohol,
solvents, abrasive cleaning agents,
or citrus-based cleaners that can
damage the plastic surface of the
device when cleaning it.
Caution: Make Interface Harness
connections to the Host Machine
shorter than 9.84 Feet (3 Meters) in
length. Cut off all unused portions
of the Interface Harness wiring to
avoid static electrical effects or
short circuit possibilities that
could cause damage to the Unit.
WARNING: This Unit is designed
for use with a Current limiting
Power Source! Design the Host
Cabinet space to meet all local
related safety standards.