background image

With this data you can calculate the following values:

Based on the following table, determine if the layout is

authorised as well as the deflector position:

CO2 must be measured at the terminal during rated operation 
and it must be 5.5%. If this is not the case, the deflector 
height must be adjusted.

CONNECTING GAS

The appliance is delivered fully equipped with:

-

A burner assembly installed in the combustion 
chamber (1)

-

A solenoid valve block and the gas fittings between 
the burner and the solenoid valve block (2)

-

A receiver connected to the solenoid valve block (3)

-

A power cord (4)

-

A remote control synchronised with the receiver

After installing the hood and the ducts, it is necessary to

verify again that the valve can move freely. In order to do so,

lift it several times at the maximum from the inside of the

fireplace.

ADJUSTING THE HEIGHT OF THE DEFLECTOR

Depending on the layout and the number of horizontal, 

vertical, oblique and elbow pieces, the height of the deflector 

in the appliance must be set to one of 6 positions. Position 1 

is the most open position (low draw) and position 6 the most 

closed position (strong draw).

Adjustment is done by removing the 2 screws from each 

bracket, retracting the bracket on the deflector to put it in the 

correct position and tightening the screws once more. Do this 

on each bracket individually to make it easier.

HOW TO CALCULATE THE DEFLECTOR POSITION

In order to verify and calculate the deflector position, a 
sketch of the required layout should be made, and the 
following table should be filled in.

Please note that the minimum requirements for configuration 

C11 are: 1 vertical metre + 1 elbow at 90

°

+ horizontal 

terminal.

Description

Abbreviation

Measured 

value

Number of vertical metres

(1)

…. metres

Number of horizontal metres

(2)

…. metres

Number of metres at an angle of 45°

(3)

…. metres

Number of elbows up to 45° (x0.5m)

(4)

…. metres

Number of elbows up to 90° (x1m)

(5)

…. metres

Description

Abbreviation

Results

Total resistance length 

= (1)+(2)+(3)+(4)+(5)

L

…. metres

Total vertical length = (1)

V

…. metres

Total horizontal length 

= (2)+(3)+(4)+(5)

H

…. metres

Total vertical length minus total 

horizontal length = V-H

R

…. metres

Conditions

Layout 

Authorisation

Deflector 

Position

L > 12

Non authorised

/

V < 1

Non authorised

/

(2) > 3

Non authorised

/

R < -1

Non authorised

/

-1 < R < 0

Authorised

1

0 < R < 1

Authorised

2

1 < R < 2

Authorised

3

2 < R < 3

Authorised

4

3 < R < 4

Authorised

5

4 < R

Authorised

6

Pressure release

valve

Deflector adjustement (x3)

Déflector

6

5

2

4

1

3

1

3

2

4

INSTALLATION OF THE APPLIANCE

1. INSTALLATION INSTRUCTIONS

Summary of Contents for EVA992GAZ



























Reviews: