background image

SAFETY WARNINGS

Only a qualified installer should install the appliance.

The gas appliances described in this manual are designed to

operate only in closed combustion chambers, i.e. with all the

glass screens and closing systems in place.

This appliance may be used by children aged 8 and over and

by people with physical, mental and sensory disabilities or

lack of knowledge or experience, as long as they are properly

monitored or if they have been instructed in the safe use of

the appliance and the inherent risks are understood.

Children should not be allowed to play with the appliance.

Cleaning and maintenance should not be performed by

unsupervised children.

Do not allow children to play with the appliance (or its remote 

control unit) or to go near the fireplace when lit or off 

(residual heat) without supervision - there is a risk of burns

All surfaces of the appliance are active surfaces and are 

therefore hot.

In case of installation in areas where children, elderly people 
or persons with disabilities can access the appliance, 
protections or other guards should be placed to prevent 
intentional or accidental contact with appliance hot surfaces. 
A 1m distance around the appliance must be provided to 
eliminate this risk.

Do not clean the appliance with water as it contains 

electronic components - there is a risk of a short-circuit or 

electrocution.

Floors, shelves and walls close to the appliance must be 

made from non-flammable materials.

Curtains must not be hung above the appliance at a distance 

of less than 1m.

If the flame supervision device has been switched off, 

intentionally or not, no reignition attempt must be made 

before 3 minutes have elapsed.

The decorative elements must be placed during installation. 

They are not accessible during normal use of the appliance. 

See Installation Instructions. 

If you smell gas: Do not smoke! Avoid open flames or sparks, 

open windows, and doors, close the gas supply tap and 

contact your installer.

If you smell gas: Do not smoke! Avoid open flames or sparks, 

open windows, and doors, close the gas supply tap and 

contact your installer.

Never use a flame to check for gas leaks.

Any operation inside the appliance must be performed by a 
qualified professional.

FIRST IGNITION

Upon the first ignition of the appliance, the final appearance 

of flames will only be visible after several hours of operation. 

Some volatile compounds (paint, grease, etc.) evaporate 

during the first hours of operation and can change the flame 

appearance.

IMPORTANT INFORMATION

2. MAINTENANCE AND USE INSTRUCTIONS

The finish paint of the appliance is a specific paint that is 

highly resistant to temperature that hardens during the first 

heating. It is very important not to touch the appliance during 

these first temperature increases so as not to damage the 

paint.

During the first heating, smoke and a smell of paint from the 

appliance may be released, this is completely normal. 

Ventilate the room to make them disappear.

MAINTENANCE OF THE APPLIANCE

Clean the lacquered parts, the painted parts, and the outside 
of the glass screen with a chamois or other soft cloth to 
prevent impurities from becoming encrusted. Perform this 
operation only when the appliance is cold and use a suitable 
commercial product. Always spray the product on the cloth 
and not directly on the surfaces to be cleaned.

Never use abrasive products.

The smoke outlet system must be cleaned at least once a 

year by a qualified professional. Its airtightness must be 

checked. Disassembly of the deflector may be needed to 

perform these operations. We suggest that you take note of 

its position before removing it in order to be able to place it 

back in the same position.

We recommend having a specialist perform full maintenance

on the appliance once a year. Airtight seals as well as safety

and operation systems will need to be checked.

WARRANTY

Your JC BORDELET appliance is covered by warranty.

All warranty conditions can be found in the “WARRANTY” 

chapter at the end of this document.

Any change or modification made to the appliance by the 
user or installer voids the warranty.

Warranty services will only be provided after registration of 
your appliance on the following website: 
https://garantie.seguin.fr/

Summary of Contents for EVA992GAZ



























Reviews: