JC BORDELET EVA992GAZ, Instructions For Installation, Maintenance And Use

Page: 4 / 26

NATURAL GAS - NG
Country FR BE DE LU PL RO NL DE
LV CY ES PT HU RO
GR HR EE FI IT LT CZ
GB SI SK AT DK IE
SE CH TR NO
Category I2E+ I2E I2EK I2ELL I2H
Gas type G20/G25 G20 G25.3 G25 G20
Gas pressure mbar 20/25mbar 20mbar 25mbar 20mbar 20mbar
Net heat output kW
10,5 10,5 10,2 8,8 10,5
Nominal heating power kW
8,2 8,2 8,0 6,6 8,2
Performance % 78,5 78,5 77,9 76,3 78,5
Performance class 2 2 2 2 2
NOx (PCS) mg/kWh 105,1 105,1 93,4 78,6 105,1
NOx class 4 4 4 5 4
Nominal gas consumption m 3 /h 1,107 1,107 1,225 1,078 1,107
Minimum gas consumption m
3
/h 0,412 0,412 0,446 0,412 0,412
Burner pressure mbar 19,1 19,1 23,9 19,0 19,1
Burner injector 2x 195/100
TECHNICAL CHARACTERISTICS
BUTANE / PROPANE
Country
FR CY ES PT BE GR IT LT
CZ GB SI IE CH TR HU RO HR EE FI DK NL
SE NO
DE LU AT CH PL
Category I3+
I3B/P I3B/P I3P
Gas type
G30/G31
G30/G31 G30/G31 G31
Gas pressure mbar
(28-30)/37 30 50 37
Net heat output kW
9,0
9,0 9,0 9,0
Nominal heating power kW
7,0
7,0 7,0 7,0
Performance %
77,7
77,7 77,7 77,7
Performance class 2
2 2 2
NOx (PCS) mg/kWh 64,6 64,6 64,6 64,6
NOx class 5
5 5 5
Nominal gas consumption m 3 /h 0,280 0,280 0,280 0,280
Minimum gas consumption m 3 /h 0,120 0,120 0,120 0,120
Burner pressure mbar 28,3
28,3 28,3 28,3
Burner injector 2x 120/100
COMMON CHARACTERISTICS
Concentric system C11 = 130/200 | C31/C91=100/150
Configuration C11/C31/C91
Minimum distance between the glass screens of the appliance and all combustible materials 1000mm
Type of backing wall material for wall-mounted appliances Non-flammable materials*
Electrical characteristics (Voltage - Intensity - Frequence – Max Power) AC: 230V – 50Hz – 2A – 30Wmax
Weight of the standalone appliance (2.5m under ceiling) 205 kg
Weight of the wall-mounted appliance (2.5m under ceiling) 200 kg
*The backing wall must be made of non-combustible material and the whole surface of the construction right-of-way must be insulated. The
insulation must be in the M0, A2s1d0 or A1 reaction-to-fire class and must have a thermal resistance higher than 0.7m².K/W (measured at
50°C). The insulation must not deteriorate at temperatures below 400°C (e.g. calcium silicate, rock mineral wool, etc.).
If the backing wall is made of combustible material, it is necessary either:
- to remove the combustible material and to install insulation as described above;
- or to place a non-combustible partition at a distance of at least 2cm from the combustible material wall and to ventilate by two openings
(bottom and top). An insulation layer must then be placed on the partition as described above.
1. INSTALLATION INSTRUCTIONS