· 9 ·
OUT OF VEHICLE:
SURFACE CHAR-
GE IN VEHICLE?
NO
TESTING
IS BATTERY
CHARGED?
YES/NO
GOOD & PASS
VOL:
xx.xx V
CCA: xxxx CCA/SAE
IR:
xx.xx mΩ
GOOD & RECHARGE
VOL:
xx.xx V
CCA: xxxx CCA/SAE
IR:
xx.xx mΩ
B. The tester will resume testing after it detects that
the surface charge is removed.
10. Test the battery for few seconds.
11.
Press the ◄ ► key to select
battery fully charged or not if
tester asks. Press «ENTER»
to confirm choice.
12. When the test is completed, the display shows the
actual volts and the actual CCA and internal resis-
tance. {Press the ◄ ► key to read: SOH (STATE
OF HEALTH) and SOC (STATE OF CHARGE)}.
13. One of the six test results will be displayed:
GOOD & PASS
*The battery is good and capa-
ble of holding a charge.
GOOD & RECHARGE
*The battery is good but needs
to be recharged.
CAUTION
VOL:
xx.xx V
CCA: xxxx CCA/SAE
IR:
xx.xx mΩ
BAD & REPLACE
VOL:
xx.xx V
CCA: xxxx CCA/SAE
IR:
xx.xx mΩ
CAUTION
*The battery may be serviced
but decrease the capability of
starting the engine gradually.
RECHARGE & RETEST
*Battery is discharged, the bat-
tery condition cannot be deter-
mined until it is fully charged.
Recharge & retest the battery.
BAD & REPLACE
*The battery will not hold a char-
ge. It should be replaced imme-
diately.
The battery may fail under extreme climate conditions.
There may be a poor connection between the vehicle
and the battery affect the charging function. Please pay
attention to the battery for replacement consideration
and charging system checking.
GOOD & PASS
SOC:
xx.xx V
■■■■■■■■■□ 90%
GOOD & PASS
SOH: xxxx CCA/SAE
■■■■■■■■■□ 90%
LOAD ERROR
CODE
xxxxxxxxxxxx
BAD CELL & REPLACE
*The battery has at least one cell
short circuit. It should be repla-
ced immediately.
LOAD ERROR
*The tested battery is bigger
than 2000CCA/SAE or 200AH.
Or the clamps are not connected properly. Please fu-
lly charge the battery and retest after excluding both
previous reasons. If reading is the same, the battery
should be replaced immediately.
What is the ”Test Code”? How to use it?
A.
Put the CD into CD or CD/DVD/BLUE RAY combi
-
nation drive.
B. Follow the installation instructions and install the
icon named “BT/RTxxx” and the sheet below will
pop up then input the “Test Code” into the chart ma-
nually or by barcode scanner.
C. Test results will show up in the chart after decoding
as below.
14. SOC & SOH Display: Press directional keys to see
SOC & SOH:
15. Test Code:
Press <Enter> to get Test Code.
PRINT RE-
SULT?
YES/NO
D. The test data can be stored in the PC.
16.
Press the ◄ ► key to select
result printing: YES or NO.
Press «ENTER» to confirm
your choice.
※
24V System Test Printing:
The printer will not function for
24 Volt batteries system test
printing.
The 24V system test result will be recorded till you
hook up to a 12V battery and the right screen shows
up. Please select “YES” and press enter key to print the
result and then disconnect the clamps. The screen will
appear again after you reconnect the clamps. Please
select “NO” and press the enter key to go back to the
main menu.
17. Press «ENTER» return to MAIN MENU or remove
the test clamps from the battery posts after comple-
tion of testing batteries to end test.
RECHARGE & RETEST
VOL:
xx.xx V
CCA: xxxx CCA/SAE
IR:
xx.xx mΩ
BAD CELL & REPLACE
VOL:
xx.xx V
CCA: xxxx CCA/SAE
IR:
xx.xx mΩ
PRINT 24V SYS
-
TEM RESULT? YES