JAI GO-2400C-PMCL User Manual Download Page 57

Page: 57 / 100

GO-2400M-PMCL / GO-2400C-PMCL

Settings List

Feature Properties

: Settings that can only be configured when image capture on the camera is stopped.

Function name

Access

type

Setting range

Min. value

Max. value

Default value

Description

a) Device Control

—

Display/configure

information related to

the device.

Device Vendor

Name

R/O

—

JAI Ltd, Japan

Display the

manufacturer name.

Device Model

Name

R/O

—

GO-2400M-PMCL

GO-2400C-PMCL

Display the model

name.

Device

Manufacturer Info

R/O

—

Digital 2.4Mega Pexel

Progresshive Scan

Display manufacturer

information.

Device Version

R/O

—

Software Version

Display the software

version.

Device Firmware

Version

R/O

—

Firm Ver. No.

Display the firmware

version.

Device Fpga

Version

R/O

—

FPGA Ver. No.

Display the FPGA

version.

Device SFNC

Version Major

R/O

—

SFNCMajorVersion

Display the SFNC

version.

Device SFNC

Version Minor

R/O

—

SFNCMinorVersion

Display the SFNC

version.

Device SFNC

Version SubMinor

R/O

—

SFNCSubMinorVersion

Display the SFNC

version.

XML Major

Version

R/O

—

XMLMajorVersion

Display the XML

version.

XML Minor

Version

R/O

—

XMLMinorVersion

Display the XML

version.

XML Sub Minor

Version

R/O

—

XMLSubMinorVersion

Display the XML

version.

Device Serial

Number

R/O

—

Varies by camera.

Display the device ID.

Device User ID

R/W

—

blank

Set the user ID for the

camera.

Device

Temperature

Selector

R/O

Mainboard

—

Mainboard

Select the area of the

camera's interior for

which to display the

temperature sensor's

reading.

Device

Temperature (C)

R/O

value ˚C

—

value ˚C

Display the internal

temperature (˚C) of

the camera.

Device Reset

W/O

—

Reset the device.

b) Image Format
Control

—

Configure image

format settings.

Sensor Width

R/O

1936

—

1936

Display the maximum

image width.

Sensor Height

R/O

1216

—

1216

Display the maximum

image height.

Sensor

Digitization Taps

R/W

Ten [10 Bit]

Twelve [12 Bit]

—

12 Bit

Displays the digital

tones output from the

sensor.

Width Max

R/O

1936

—

1936

Display the maximum

image width.

Height Max

R/O

1216

—

1216

Display the maximum

image height.

Width

R/W

Min to (Max-OffsetX)

1936

Set the image width.

Height

R/W

Min to (Max-OffsetX)

1216

Set the image height.

Summary of Contents for GO-2400C-PMCL





































































































Search results

Summary of Contents for GO-2400C-PMCL

Reviews:

Related manuals for GO-2400C-PMCL

Brands by name

Popular brands

JAI GO-2400C-PMCL, User Manual

Search results

Summary of Contents for GO-2400C-PMCL

Reviews:

Related manuals for GO-2400C-PMCL

Brands by name

Popular brands