JAI GO-2400C-PMCL User Manual Download Page 58

Page: 58 / 100

GO-2400M-PMCL / GO-2400C-PMCL

Function name

Access

type

Setting range

Min. value

Max. value

Default value

Description

Offset X

R/W

Min to Max

1840

Set the horizontal

offset.

Offset Y

R/W

Min to Max

1214

Set the vertical offset.

Binning

Horizontal

R/W

1: Off

2: x2

1: Off

Set the number of

pixels in the

horizontal direction

for which to perform

binning.

(Mono only)

Binning Vertical

R/W

1: Off

2: x2

1: Off

Set the number of

pixels in the vertical

direction for which to

perform binning.

GO-400M-PMCL only

Pixel Format

R/W

GO-2400M-PMCL:

Mono8

Mono10

Mono12

GO-2400C-PMCL:

BayerRG8

BayerRG10

BayerRG12

—

GO-2400M-PMCL:

Mono8

GO-2400C-PMCL:

BayerRG8

Set the pixel format.

Mono12 and

BayerRG12 are

available when Video

Process Bypass

Mode is set to On.

PixelColorFilter

R/O

GO-2400M-PMCL:

None

GO-2400C-PMCL:

BayerRG

—

GO-2400M-PMCL:

None

GO-2400C-PMCL:

BayerRG

Display the color filter

type that will be

applied to the image.

Test Pattern

R/W

Off [Off]

GreyHorizontalRamp [Grey

Horizontal Ramp]

GreyVerticalRamp [Grey Vertical

Ramp]

GreyHorizontalRampMoving

[Grey Horizontal Ramp Moving]

HorizontalColorBar [Horizontal

Color Bar]

VerticalColorBar [Vertical Color

Bar]

MovingColorBar [Moving Color

Bar]

—

0: Off

Select the test image.

ColorBar is only

available on the

GO-2400C-PMCL.

c) Acquisition
Control

Configure image

capture settings.

Acquisition

Frame Rate Raw

R/W

0.125 to 127.975

0.125

127.975

120.163

Set the frame rate as

a frequency. (unit: Hz)

The maximum value

varies depending on

the TapGeometory

and ROI settings.

Trigger Selector

R/O

FrameStart

[Frame Start]*

—

FrameStart

Select the trigger

operation.

Trigger Mode

R/W

Off

—

Off

Display the Trigger

mode.

Trigger Software

W/O

—

Execute a software

trigger.

Trigger Source

R/W

Low [Low]

High [High]

Software [Software]

PulseGenerator0 [Pulse

Generator 0]

UserOutput0 [User Output 0]

UserOutput1 [User Output 1]

Line4 [Line4 - TTL In]

Line 7[Line7 - CC1]

Nand0 [Nand0 Out]

Nand1 [Nand1 Out]

—

Line 7 [Line7- CC1]

Select the trigger

signal source.

Line4 TTL In is

available on Standard

Model.

Trigger Activation R/W

RisingEdge [Rising Edge]

FallingEdge [Falling Edge]

LevelHigh [Level High]

LevelLow [Level Low]

—

Rising Edge

Select the polarity of

the trigger signal (i.e.,

location of signal at

which trigger is

applied).

Summary of Contents for GO-2400C-PMCL





































































































Search results

Summary of Contents for GO-2400C-PMCL

Reviews:

Related manuals for GO-2400C-PMCL

Brands by name

Popular brands

JAI GO-2400C-PMCL, User Manual

Search results

Summary of Contents for GO-2400C-PMCL

Reviews:

Related manuals for GO-2400C-PMCL

Brands by name

Popular brands