JAI GO-2400C-PMCL User Manual Download Page 21

Page: 21 / 100

GO-2400M-PMCL / GO-2400C-PMCL

Control without external triggers

When controlling the exposure time using specified exposure times

Configure the settings as follows.

Item

Setting value / selectable range

Trigger Selector (trigger operation)

Frame Start

Trigger Mode

Off

Exposure Mode

Timed (control via exposure time)

Exposure Time

Varies depending on the Tap Geometry and CL Pixel Clock

settings. *

Exposure Auto

Off, Continuous

* 1 Max. value = [Acquisition Frame Rate] - Max. exposure time value A (“Exposure times” (page 19))

Set [Exposure Mode] to [Timed].

([Timed] is the default setting.)

Specify the exposure time in [Exposure Time].

The setting value for the exposure time can only be changed when [Exposure Auto] is set to [Off].
If [Exposure Auto] is set to [Continuous], temporarily set it to [Off] before changing the [Exposure
Time].

Set [Trigger Mode] to [On].

If necessary, change the [Exposure Auto] setting.

When not controlling the exposure time

Configure the settings as follows.

Item

Setting value / selectable range

Exposure Mode

Off

The exposure will be performed with an exposure time equal to 1 / frame rate.

* The [Exposure Time] setting will be disabled, and the [Exposure Auto] function cannot be used.

Summary of Contents for GO-2400C-PMCL





































































































Search results

Summary of Contents for GO-2400C-PMCL

Reviews:

Related manuals for GO-2400C-PMCL

Brands by name

Popular brands

JAI GO-2400C-PMCL, User Manual

Search results

Summary of Contents for GO-2400C-PMCL

Reviews:

Related manuals for GO-2400C-PMCL

Brands by name

Popular brands