JAI GO-2400C-PMCL User Manual Download Page 85

Page: 85 / 100

GO-2400M-PMCL / GO-2400C-PMCL

LUTMode

R/W

LUTC

0: Off

1: Gamma

2: LUT

LUTC=[Param.]<CR><LF>

LUTC?<CR><LF>

Select the JAI LUT

mode.

AlcSpeed

R/W

ALCS

Min to Max

ALCS=[Param.]<CR><LF>

ALCS?<CR><LF>

for AGC and ASC

Set the control

speed for AGC and

ASC (8 is the

fastest).

AwbSpeed

R/W

AWBS

Min to Max

AWBS=[Param.]<CR><LF>

AWBS?<CR><LF>

for AWB

Set the control

speed for Balance

White Auto (AWB)

(8 is the fastest).

ExposureAutoMax

R/W

ASCEA

Min to Max[us]

101

8000000

18000

ASCEA=[Param.]<CR><LF>

ASCEA?<CR><LF>

Maximum value is varied

depending on frame rate.

Set the maximum

value for the

Exposure Auto

(ASC) control

range.

ExposureAutoMin

R/W

ASCEI

Min to Max

100

7999999

100

ASCEI=[Param.]<CR><LF>

ASCEI?<CR><LF>

Maximum value is varied

depending on frame rate.

Set the minimum

value for the

Exposure Auto

(ASC) control

range.

AlcReference

R/W

AGCF

Min to Max[%]

100

AGCF=[Param.]<CR><LF>

AGCF?<CR><LF>

Set the target

level for ALC.

(unit: %)

GainAutoMax

R/W

AGCGA

Min to Max

101

1600

AGCGA=[Param.]<CR><LF>

AGCGA?<CR><LF>

Set the maximum

value for the Gain

Auto (AGC)

control range.

GainAutoMin

R/W

AGCGI

Min to Max

100

1599

100

AGCGI=[Param.]<CR><LF>

AGCGI?<CR><LF>

Set the minimum

value for the Gain

Auto (AGC)

control range.

ALCChannelAreaAll

R/W

ALCA

0: Off / 1: On

ALCA=[Param.]<CR><LF>

ALCA?<CR><LF>

On: Specify all

photometry areas

for ALC,

regardless of the

enabled/disabled

statuses

configured

individually for

each photometry

area with [ALC

Area Selector].

Off: Specify areas

for ALC based on

the enabled/

disabled statuses

configured

individually for

each photometry

area with [ALC

Area Selector].

ALCChannelArea

LowRight

R/W

ALCLR

0: Off / 1: On

ALC**=[Param.]<CR><LF>

ALC**?<CR><LF>

Enable/disable

the Low Right

photometry area.

ALCChannelArea

LowMidRight

R/W

ALCLMR

0: Off / 1: On

Enable/disable the

Low Mid Right

photometry area.

ALCChannelArea

LowMidLeft

R/W

ALCLML

0: Off / 1: On

Enable/disable the

Low Mid Left

photometry area.

ALCChannelArea

LowLeft

R/W

ALCLL

0: Off / 1: On

Enable/disable

the Low Left

photometry area.

ALCChannelArea

MidLowRight

R/W

ALCMLR

0: Off / 1: On

Enable/disable the

Mid Low Left

photometry area.

ALCChannelArea

MidLowMidRight

R/W

ALCMLMR

0: Off / 1: On

Enable/disable

the Mid Low Mid

Right photometry

area.

Summary of Contents for GO-2400C-PMCL





































































































Search results

Summary of Contents for GO-2400C-PMCL

Reviews:

Related manuals for GO-2400C-PMCL

Brands by name

Popular brands

JAI GO-2400C-PMCL, User Manual

Search results

Summary of Contents for GO-2400C-PMCL

Reviews:

Related manuals for GO-2400C-PMCL

Brands by name

Popular brands