JAI GO-2400C-PMCL User Manual Download Page 62

Page: 62 / 100

GO-2400M-PMCL / GO-2400C-PMCL

Function name

Access

type

Setting range

Min. value

Max. value

Default value

Description

Pulse Generator

Clear Source

R/W

Low [Low]

High [High]

FrameTriggerWait [Frame Trigger

Wait]

FrameActive [Frame Active]

ExposureActive [Exposure

Active]

FVAL [FVAL]

LVAL [LVAL]

UserOutput0 [User Output 0]

UserOutput1 [User Output 1]

Line4 [Line4 - TTL In]

Line7 [Line7 - CC1]

Nand0 [Nand0 Out]

Nand1 [Nand1 Out]

—

0: Low

Select the count clear

input signal source.

Line4 TTL In is

available on Standard

Model.

Pulse Generator

Clear Inverter

R/W

True, False

—

FALSE

Select whether to

invert the polarity of

the count clear input

signal.

Pulse Generator

Clear Sync Mode

R/W

AsyncMode [Async Mode]

SyncMode [Sync Mode]

—

Async Mode

Select the sync mode

for the count clear

input signal.

g) LUTControl

Configure LUT

settings.

LUT Selector

R/W

Red

Green

Blue

—

GO-2400M-PMCL:

1: Mono

GO-2400C-PMCL:

1: Green

Select the LUT

channel to control.

This item is not

displayed for the

GO-2400M-PMCL.

LUT Index

R/W

0 to 255

255

Set the LUT index

table number.

LUT Value

R/W

0 to 4095

4095

Set the LUT value.

h) TransportLayerControl

Configure Camera

Link Transport Layer

settings.

Device Tap

Geometry

R/W

Geometry_1X2_1Y

Geometry_1X3_1Y

Geometry_1X4_1Y

Geometry_1X8_1Y

—

3: 1X4_1Y

Set the transmission

method for each time

images are

transmitted from the

device (TAP

structure).

Camera Link

Clock Frequency

R/W

CameraLinkClock37_1MHz

[37.1MHz]

CameraLinkClock74_3MHz

[74.3MHz]

CameraLinkClock84_9MHz

[84.9MHz]

—

1: 74.3MHz

Set the Camera Link

clock.

h)
UserSetControl

Load factory default

settings or save/load

user settings for

camera settings.

UserSet Selector

R/W

Default [Default]

User1 [User1]

User2 [User2]

User3 [User3]

0: Default

(factory default values)

Select the user

settings.

UserSet Load

W/O

—

Load user settings.

UserSet Save

W/O

—

Save the current

setting values as user

settings.

i) JAICustomControl

Configure settings for

functions that are

unique to JAI

cameras and not

specified by SFNC.

Video Process

Bypass Mode

R/W

Off

—

Off

Enable/ disable video

process bypass

mode.

Summary of Contents for GO-2400C-PMCL





































































































Search results

Summary of Contents for GO-2400C-PMCL

Reviews:

Related manuals for GO-2400C-PMCL

Brands by name

Popular brands

JAI GO-2400C-PMCL, User Manual

Search results

Summary of Contents for GO-2400C-PMCL

Reviews:

Related manuals for GO-2400C-PMCL

Brands by name

Popular brands