ITech IT9120 Series Programming Manual Download

Page: 83 / 90

Calibration Commands

calibration constants from nonvolatile memory.

Command Syntax

CALibrate:INITial

Parameters

None

Example

CAL:INIT

Relevant command

CAL:STAT CAL:INIT
CHAN:FACtory:SAVe

Command Syntax

CHAN:FACtory:SAVe

Parameters

None

CALibrate:SAVe

This command can only be used in calibration mode. It saves any new
calibration constants (after a current or voltage calibration procedure has been
completed) in nonvolatile memory.

Command Syntax

CALibrate:SAVE

Parameters

None
Example:CAL:SAVE

Relevant command

CAL:STAT CAL:INIT

CALibrate:CURRent:POINt

This command is used to specify the current calibration points.
Command Syntax:
CALibrate:CURRent:POINt <point>

Parameters

P1 | P2 | P3 | P4
Example:CAL:CURR:POIN P2

Relevant command

CAL:STAT CAL:SAV

Summary of Contents for IT9120 Series



























































































Search results

Summary of Contents for IT9120 Series

Reviews:

Related manuals for IT9120 Series

Brands by name

Popular brands

ITech IT9120 Series, Programming Manual

Search results

Summary of Contents for IT9120 Series

Reviews:

Related manuals for IT9120 Series

Brands by name

Popular brands