Isuzu 4HL1 Workshop Manual Download Page 153

Page: 153 / 267

Engine Control System 1A-151

Check the ECM ground circuit for open wiring.

Starter switch "OFF".

Disconnect the ECM.

Measure the resistance between ECM
connector pin and ground (e.g., frame or
body)

Was the resistance within range?

Pins 87/95/

119/120/121-

ground: 0

Ω

Go to Step 6

Go to Step 5

Repair or replace the faulty harness.

Is the action complete?

—

Verify repair and

go to Step 6

—

Replace the ECM.

IMPORTANT:
If necessary (for the vehicle equipped with
idle stop function), input the number of
startups to the replacing ECM.

Is the action complete?

—

Verify repair and

go to Step 7

—

Check DTC51 will not be set again.

Using Tech 2, clear the DTC.

Start the engine and review the DTC.

Is DTC51 detected?

—

Refer to

Diagnostic Aids

and go to Step 1

Repair is

complete

Step

Action

Value(s)

Yes

Summary of Contents for 4HL1












































































































































































































































































Search results

Summary of Contents for 4HL1

Reviews:

Related manuals for 4HL1

Brands by name

Popular brands

Isuzu 4HL1, Workshop Manual

Search results

Summary of Contents for 4HL1

Reviews:

Related manuals for 4HL1

Brands by name

Popular brands