Isuzu 4HL1 Workshop Manual Download Page 219

Page: 219 / 267

Engine Control System 1A-217

Check the SCV.

At the SCV connector pins, measure the
resistance.

Was the resistance within range?

Ω

Go to Step 10

Go to Step 8

Replace the supply pump (SCV).

Is the action complete?

—

Verify repair and

go to Step 9

—

Check DTC247 will not be set again.

Restore the vehicle.

Bleed the air from the fuel system.

Using Tech 2, clear the DTC.

Perform test run and review the DTC.

Is DTC247 detected?

—

Refer to

Diagnostic Aids

and go to Step 2

Repair is

complete

Review the DTC.

Certainly connect the SCV and ECM
connectors.

Using Tech 2, clear the DTC.

Perform test run and review the DTC.

Is DTC247 detected?

—

Go to Step 11

Refer to

Diagnostic Aids

Replace the ECM.

IMPORTANT:
If necessary (for the vehicle equipped with
idle stop function), input the number of
startups to the replacing ECM.

Is the action complete?

—

Verify repair and

go to Step 12

—

Check DTC247 will not be set again.

Using Tech 2, clear the DTC.

Perform test run and review the DTC.

Is DTC247 detected?

—

Refer to

Diagnostic Aids

and go to Step 2

Repair is

complete

Step

Action

Value(s)

Yes

Summary of Contents for 4HL1












































































































































































































































































Search results

Summary of Contents for 4HL1

Reviews:

Related manuals for 4HL1

Brands by name

Popular brands

Isuzu 4HL1, Workshop Manual

Search results

Summary of Contents for 4HL1

Reviews:

Related manuals for 4HL1

Brands by name

Popular brands