Isuzu 4HL1 Workshop Manual Download Page 148

Page: 148 / 267

1A-146 Engine Control System

EGR Valve Description

Legend

1. Exhaust path
2. Valve
3. Motor (–)
4. Sensor signal

5. Sensor ground
6. Sensor power
7. Motor (+)
8. DC motor

Replace the EGR valve (EGR DC motor).

Is the action complete?

—

Verify repair and

go to Step 10

—

Review the DTC.

Certainly connect the EGR valve position
sensor and ECM connectors.

Using Tech 2, clear the DTC.

Perform test run and review the DTC.

Is DTC45 detected?

—

Go to Step 9

Refer to

Diagnostic Aids

Replace the ECM.

IMPORTANT:
If necessary (for the vehicle equipped with
idle stop function), input the number of
startups to the replacing ECM.

Is the action complete?

—

Verify repair and

go to Step 10

—

Check DTC45 will not be set again.

Using Tech 2, clear the DTC.

Perform test run and review the DTC.

Is DTC45 detected?

—

Refer to

Diagnostic Aids

and go to Step 2

Repair is

complete

Step

Action

Value(s)

Yes

LNW21ASF002201

Summary of Contents for 4HL1












































































































































































































































































Search results

Summary of Contents for 4HL1

Reviews:

Related manuals for 4HL1

Brands by name

Popular brands

Isuzu 4HL1, Workshop Manual

Search results

Summary of Contents for 4HL1

Reviews:

Related manuals for 4HL1

Brands by name

Popular brands