Invertek Drives OPTIDRIVE E3, User Manual

Page: 40 / 52

40
| Optidrive ODE-3 IP66 Outdoor Rated User Guide |
Version 1.00 www.invertekdrives.com
7.5. Macro Functions - Keypad Mode (P-12 = 1 or 2)
P-15
DI1 DI2 DI3 / AI2 DI4 / AI1 Diagram
0 1 0 1 0 1 0 1
0
STOP ENABLE - INC SPD  - DEC SPD  FWD  REV  8
^----------------START----------------^
1
STOP ENABLE PI Speed Reference
2
STOP ENABLE - INC SPD

- DEC SPD

KPD REF P-20 REF 8
^----------------START----------------^
3
STOP ENABLE - INC SPD  E-TRIP OK - DEC SPD  9
^-------------------------------START-------------------------------^
4
STOP ENABLE -
INC SPD
 KPD REF AI1 REF AI1 10
5
STOP ENABLE FWD  REV  KPD REF AI1 REF AI1 1
6
STOP ENABLE FWD  REV  E-TRIP OK KPD REF P-20 REF 11
7
STOP RUN FWD STOP RUN REV  E-TRIP OK KPD REF P-20 REF 11
^---------FAST STOP (P-24)---------^
8
STOP RUN FWD  STOP RUN REV  KPD REF AI1 REF AI1
14
STOP RUN - - E-TRIP OK - -
15
STOP RUN PR REF KPD REF Fire Mode P-23 P-21 2
16
STOP RUN P-23 REF KPD REF Fire Mode
FWD

REV
 2
17
STOP RUN KPD REF P-23 REF Fire Mode FWD  REV  2
18
STOP RUN AI1 REF KPD REF Fire Mode AI1 1
9, 10, 11, 12, 13 = Behavior as per setting 0
7.6. Macro Functions - Fieldbus Control Mode (P-12 = 3, 4, 7, 8 or 9)
P-15
DI1 DI2 DI3 / AI2 DI4 / AI1 Diagram
0 1 0 1 0 1 0 1
0
STOP ENABLE FB REF (Fieldbus Speed Reference, Modbus RTU / CAN / Master-Slave
defined by P-12)
14
1
STOP ENABLE PI Speed Reference 15
3
STOP ENABLE FB REF P-20 REF E-TRIP OK Analog Input AI1 3
5
STOP ENABLE FB REF PR REF P-20 P-21 Analog Input AI1 1
^----START (P-12 = 3 or 4 Only)----^
6
STOP ENABLE FB REF AI1 REF E-TRIP OK Analog Input AI1 3
^----START (P-12 = 3 or 4 Only)----^
7
STOP ENABLE FB REF KPD REF E-TRIP OK Analog Input AI1 3
^----START (P-12 = 3 or 4 Only)----^
14
STOP ENABLE - - E-TRIP OK Analog Input AI1 16
15
STOP ENABLE PR REF FB REF Fire Mode P-23 P-21 2
16
STOP ENABLE P-23 REF FB REF Fire Mode Analog Input AI1 1
17
STOP ENABLE FB REF P-23 REF Fire Mode Analog Input AI1 1
18
STOP ENABLE AI1 REF FB REF Fire Mode Analog Input AI1 1
2, 4, 8, 9, 10, 11, 12, 13 = Behavior as per setting 0
Analog and Digital Input Macr
o Configurations
7