background image

46

GUARANTEE AND WARRANTY

sMove controller 

 Installation and operating manual

12 

Guarantee and warranty

Warranty

Outside Germany, the national warranty provisions of the country in which the system is sold 

apply. Please contact the distributor for your country.

The warranty refers to the defect-free condition of the product at the time of purchase and cov-

ers all defects that were present at the time of purchase. Failure to observe the intended use 

will invalidate all warranty claims.

Manufacturer guarantee

inVENTer GmbH provides a five-year guarantee for all electrical components and the wall  

mounting sleeve, as well as a thirty-year guarantee on the heat accumulator ceramic.  

This covers premature product wear.

Further information about the warranty is available at www.inventer.eu/warranty.

13 

Service

Claims

Check the delivery for completeness and transport damage upon receipt using the delivery 

note. Report missing items immediately, and at the latest within 14 days to your supplier,  

distributor or factory representative.

Warranty and guarantee claims

In the case of a warranty or guarantee claim, contact your local distributor or factory represent-

ative.

In all cases, please return the complete device to the manufacturer.  

The guarantee is an additional offer by the manufacturer and in no way affects the applicable 

law.

Accessories and spare parts

To order parts for your controller, contact your nearest factory outlet or our service staff.

Technical customer service

For technical support contact our service staff.

+49 (0) 36427 211-0

+49 (0) 36427 211-113

[email protected]

http://www.inventer.eu

Summary of Contents for sMove S4 Long

















































Reviews: