background image

14

Pulsar extractor fan 

 Installation and operating instructions

4.2  Electrical connection 12 V DC (direct current)

TIP: 

Have the extractor fan‘s 12 V DC connection carried out by qualified personnel.

Terminal assignment for operating voltage cable

Figure 9: PCB of Pulsar extractor fan: terminal assignment for connecting terminal 12 V DC

Installing the power supply unit (optional)

DANGER
Exposed electrical components.

Electric shock and injury due to live components (230 V, 50 Hz)!

 

Before working on electrical installations, disconnect all affected equipment from the power supply.

 

Do not connect the power supply unit under voltage.

 

The connection must only be performed by qualified and trained personnel.

DANGER
Ingress of water into the power supply unit.

Electric shock and overheating due to short circuit (230V, 50Hz)!

 

Install power supply unit outside protection areas 0 to 2.

ELECTRICAL CONNECTION

3

2

7

4

6

4

1

5

1  Cable inlet for operating voltage cable
2  Cable feed-through for operating voltage 

cable

3  Operating voltage cable, 12 V DC, 2-wire
4  Connecting terminal for operating voltage 

cable

5  PCB
6  Terminal –     (black)
7  Te     (red)

Summary of Contents for Pulsar





































Reviews: