manualshive.com logo in svg

Intel PXA255, Developer'S Manual

The Intel PXA255 product is a high-performance processor designed for a range of mobile devices. Obtain detailed specifications and technical information about this product by downloading the free datasheet and user manual from our website. Experience the power and versatility of Intel PXA255 for your mobile devices.

Share
Download
background image

Intel® PXA255 Processor Developer’s Manual

7-33

 

LCD Controller

word[1] contains the value for FSADRx
word[2] contains the value for FIDRx
word[3] contains the value for LDCMDx

Software must write the location of the first descriptor to FDADRx before enabling the LCD 

controller. Once the controller is enabled, the first descriptor is read, and all four registers are 

written by the DMAC. The next frame descriptor pointed to by FDADRx is loaded into the 
registers for the associated DMA channel after all data for the current descriptor has been 

transferred.

The address in FDADRx is not used when the BRA bit in the Frame Branch Register (FBRx) is set. 

In this case, the Frame Branch Address is used to fetch the descriptor for the next frame. Branches 

can be used to load a new palette or to process a regular frame, as detailed in 

Section 7.6.6

.

Note:

If only one frame buffer is used in external memory, the FDADRx field (word[0] of the frame 
descriptor) must point back to itself.

7.6.5.2

LCD DMA Frame Descriptor Address Registers (FDADRx)

FDADR0 and FDADR1, shown in 

Table 7-7

, correspond to DMA channels 0 and 1 and contain the 

memory address of the next descriptor for the DMA channel. The DMAC fetches the descriptor at 
this location after finishing the current descriptor. On reset, the bits in this register are undefined. 

The target address must be aligned to a 16-byte boundary. Bits [2:0] of the address must be zero.

These are read/write registers. Ignore reads from reserved bits. Write zeros to reserved bits.

7.6.5.3

LCD DMA Frame Source Address Registers (FSADRx)

FSADR0 and FSADR1, shown in 

Table 7-8

, correspond to DMA channels 0 and 1 and contain the 

source address of the current descriptor for the DMA channel. The address must be aligned on an 

8-byte boundary. Bits [2:0] must be zero. If this descriptor is a palette load, FSADRx points to the 

memory location at the beginning of the palette data. The size of the palette data must be four 16-

bit entries for 1- and 2-bit pixels, sixteen 16-bit entries for 4-bit pixels, or 256 16-bit entries for 8-
bit pixels. If this descriptor is for pixel data, FSADRx points to the beginning of the frame buffer in 

memory. This address is incremented as the DMAC fetches from memory. If desired, the DMA 

Frame ID Register can be used to hold the initial frame source address. 

These read-only registers are loaded indirectly via the frame descriptors, as described in 

Section 7.6.5.1

.

Table 7-7. FDADRx Bit Definitions 

Physical Address

channel 0: 0x4400_0200
channel 1: 0x4400_0210

FDADR0 
FDADR1

LCD Controller

Bit

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9

8

7

6

5

4

3

2

1

0

Descriptor Address

Reset ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?

Bits

Name

Description

31:0

Descriptor 

Address

Address of next descriptor.
Bits [2:0] must be zero for proper memory alignment.

Summary of Contents for PXA255

























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PXA255

dbx 902 Manual preview
902
Brand: dbx Pages: 8
EAW MX8000 Technical Specifications preview
MX8000
Brand: EAW Pages: 2
3xLogic V250 Quick Start Manual preview
V250
Brand: 3xLogic Pages: 2
Palm M505 Setting Up preview
M505
Brand: Palm Pages: 4
Datasat AP25 Installation And Operating Manual preview
AP25
Brand: Datasat Pages: 170
Blackmagicdesign Teranex 2D Processor Installation And Operation Manual preview
Teranex 2D Processor
Brand: Blackmagicdesign Pages: 969
C&T Solution VCO-6131E-4M2 User Manual preview
VCO-6131E-4M2
Brand: C&T Solution Pages: 129
AXAGO PCEU-43R Quick Installation Manual preview
PCEU-43R
Brand: AXAGO Pages: 2
Altera Stratix II User Manual preview
Stratix II
Brand: Altera Pages: 33
ICP DAS USA I-87K Series User Manual preview
I-87K Series
Brand: ICP DAS USA Pages: 31
LUX LUMEN 10230 Manual preview
10230
Brand: LUX LUMEN Pages: 41
GSA Bolide BN-NVR/NX User Manual preview
Bolide BN-NVR/NX
Brand: GSA Pages: 101
Areca ARC-12x4 Series Quick Installation Manual preview
ARC-12x4 Series
Brand: Areca Pages: 2
LevelOne NVR-0432 User Manual preview
NVR-0432
Brand: LevelOne Pages: 142
ACTi GNR-410 Quick Installation Manual preview
GNR-410
Brand: ACTi Pages: 12
Airaya AI108-1-050 Quick Install Manual preview
AI108-1-050
Brand: Airaya Pages: 28
LinMot E1100 Series Manual preview
E1100 Series
Brand: LinMot Pages: 62
Thermaltake CLP0539 Installation Manual preview
CLP0539
Brand: Thermaltake Pages: 1

Brands by name

Popular brands

Load more brands