manualshive.com logo in svg

Intel PXA255, Developer'S Manual

The Intel PXA255 product is a high-performance processor designed for a range of mobile devices. Obtain detailed specifications and technical information about this product by downloading the free datasheet and user manual from our website. Experience the power and versatility of Intel PXA255 for your mobile devices.

Share
Download
background image

Intel® PXA255 Processor Developer’s Manual

11-1

Fast Infrared Communication Port

11

The Fast Infrared Communications Port (FICP) for the PXA255 processor operates at half-duplex 

and provides direct connection to commercially available Infrared Data Association (IrDA) 

compliant LED transceivers. The FICP is based on the 4-Mbps IrDA standard and uses four-

position pulse modulation (4PPM) and a specialized serial packet protocol developed for IrDA 
transmission. To support the standard, the FICP has:

•

A bit encoder/decoder, 

•

A serial-to-parallel data engine 

•

A transmit FIFO 128 entries deep and 8 bits wide

•

A receive FIFO 128 entries deep and 11 bits wide

The FICP shares GPIO pins for transmit and receive data with the Standard UART. Only one of the 
ports can be used at a time. To support a variety of IrDA transceivers, both the transmit and receive 

data pins can be individually configured to communicate using normal or active low data. 

11.1

Signal Description

The FICP signals are IRRXD and IRTXD. 

Table 11-1

 describes each signal’s function. Most IrDA 

transceivers also have enable and speed pins. Use GPIOs to enable the transceiver and select the 

speed. See 

Chapter 4, “System Integration Unit”

 for more information.

 

11.2

FICP Operation

The FICP is disabled and does not have control of the port’s pins after a reset. Before software 
enables the FICP for high-speed operation, it must set the control registers to reflect the desired 

operating mode. After the control registers are set, software can either preload the FICP’s transmit 

FIFO with up to 128 bytes, or leave the FIFO empty and use the DMA to service it after the FICP 

is enabled. Once the FICP is enabled, transmit/receive data can be sent on the transmit and receive 

pins.

The transmit/receive data is modulated according to the 4PPM IrDA standard and converted to 

serial or parallel data. The modulation technique and the frame format are discussed in the sections 

that follow.

Table 11-1. FICP Signal Description

Signal Name

Input/Output

Description

IRRXD

Input

Receive pin for FICP

IRTXD

Output

Transmit pin for FICP

Summary of Contents for PXA255

























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PXA255

Canon Vb-C60 - Ptz Network Camera Setup Manual preview
Vb-C60 - Ptz Network Camera
Brand: Canon Pages: 30
Cabletron Systems Netlink FRX4000 Installation And Setup Manual preview
Netlink FRX4000
Brand: Cabletron Systems Pages: 8
Cabletron Systems 9C300-1 Upgrade Instructions preview
9C300-1
Brand: Cabletron Systems Pages: 4
Vivotek NR8401 User Manual preview
NR8401
Brand: Vivotek Pages: 136
Supermicro SuperServer 5019S-L User Manual preview
SuperServer 5019S-L
Brand: Supermicro Pages: 61
Time domain PulsON 440 Datasheet And User Manual preview
PulsON 440
Brand: Time domain Pages: 64
ICP DAS USA PDS-734D Quick Start Manual preview
PDS-734D
Brand: ICP DAS USA Pages: 8
WAGO 750-459 Manual preview
750-459
Brand: WAGO Pages: 48
Cypress PSoC 4 S Series Quick Start Manual preview
PSoC 4 S Series
Brand: Cypress Pages: 4
Dolby Laboratories Digital Loudspeaker Brochure preview
Digital Loudspeaker
Brand: Dolby Laboratories Pages: 4
Comelit IPNVR016A User Manual preview
IPNVR016A
Brand: Comelit Pages: 140
TDK HHM Series HHM1521 Specifications preview
HHM Series HHM1521
Brand: TDK Pages: 2
Vantec Aeroflow FX 120 VAF-1225 User Manual preview
Aeroflow FX 120 VAF-1225
Brand: Vantec Pages: 2
Digi NS7520B Series Hardware Reference Manual preview
NS7520B Series
Brand: Digi Pages: 339
Fortec Star Diamond Systems DS-MPE-CAN2L Manual preview
Diamond Systems DS-MPE-CAN2L
Brand: Fortec Star Pages: 36
Rohm BD7682FJ-EVK-301 Quick Start Manual preview
BD7682FJ-EVK-301
Brand: Rohm Pages: 6
Calix GigaSpire BLAST u6 Setup Manual preview
GigaSpire BLAST u6
Brand: Calix Pages: 9
Hitachi KNX001 Installation And Operation Manual preview
KNX001
Brand: Hitachi Pages: 14

Brands by name

Popular brands

Load more brands